Heating and Cooling Ecorse

Completed comprehensive Gold-level furnace inspection on 13-year-old unit located in basement. Performed thorough examination of all internal mechanical and electrical components including blower motor assembly, burner assembly, heat exchanger, electrical connections, and wiring harness. Verified proper operation of all system components and documented equipment condition with photographic records.

Performed routine maintenance tune-up on a gas furnace less than 5 years old located in basement. Conducted comprehensive inspection of all system components including gas valve, burner assembly, and electrical connections. Verified proper ignition sequence and observed clean blue flame pattern across burner ports, indicating optimal combustion. Inspected and replaced 16x25x1 air filter which showed dust accumulation. Checked all wiring connections, tested safety controls, and confirmed unit operating within normal parameters. No deficiencies or repairs required at this time.

Responded to water leak complaint in utility room. Upon inspection, identified leaking pipes connected to Rheem water heater. Assessed plumbing connections, valves, and supply lines for source of leak. Documented equipment condition and leak location through photo documentation of water heater, surrounding piping infrastructure, and HVAC system in mechanical space. Provided customer with findings and recommended repair options to resolve active leak condition.

Completed comprehensive A/C system inspection on residential cooling unit. Performed electrical diagnostics using clamp meter, recording amperage draw of 23.75 amps at condenser unit. Inspected indoor mechanical components including gas line connections with shutoff valve, PVC condensate drain system, and electrical wiring connections. Evaluated outdoor condenser unit condition, noting normal operational wear and proper electrical terminal connections. System operating within normal parameters at time of inspection.

Completed NSP AC inspection on 3-year-old system with basement coil and furnace. Verified operation of ASPEN refrigerant evaporator coil (Model DC24A3G-175L-416) containing R-410A refrigerant at 448 PSI design pressure. Inspected Honeywell Home air filter (Model FC100A1029, 16x25x4, MERV 11 rating) and provided customer education regarding proper filter maintenance intervals and MERV rating specifications for optimal system performance and air quality.

Responded to leak investigation and completed stack rebuild, toilet, and flange repair per approved estimate. Rebuilt plumbing stack system, replaced toilet flange, and reinstalled toilet assembly to resolve water leak issue. Verified all connections were properly sealed, tested system for leaks, and confirmed water supply was functioning correctly upon completion.

Completed installation of a new 70,000 BTU ECM furnace system with associated thermostat and condensate pump. Obtained mechanical and electrical permits prior to installation and ensured all work met local code requirements. Installed new PVC venting system, established proper electrical connections, configured gas supply lines, and verified all safety controls and operational parameters. System tested and confirmed operational, with utility rebate documentation submitted for energy-efficient equipment.

Provided estimate for complete furnace replacement following previous shutdown due to critical safety issues including seized inducer motor, failed blower motor with significant oil leakage, and cracked heat exchanger. The 10+ year old natural gas furnace located in basement was deemed non-operational and unsafe for continued use. Assessed existing ductwork configuration and utility connections to determine replacement specifications for new equipment installation.

Responded to service call for leaking downstairs wastewater pipe in basement area. Upon inspection, identified compromised PVC drainage piping running along concrete block foundation wall. Assessed plumbing system configuration including vertical and horizontal drain lines with multiple joints and fittings. Evaluated pipe connections and determined source of water leak in wastewater drainage system. Completed necessary repairs to eliminate active leak and restore proper drainage function. Verified system integrity and confirmed no additional moisture intrusion following repair completion.

Responded to service call for a clogged drain in basement laundry area that had been problematic for approximately 5 days. Upon inspection, removed floor drain cleanout access cap and identified significant buildup of debris restricting water flow. Successfully cleared the blockage using appropriate snaking equipment, restored proper drainage function, and documented the condition with photos before and during service.

Performed comprehensive tune-up on 12-year-old HVAC system located in basement. Noted previous water damage with visible flood mark on unit exterior. Conducted electrical diagnostics using multimeter, verifying proper voltage readings and electrical connections. System is operational but shows signs of age and previous water exposure.