Heating and Cooling Shelby Township

Completed full HVAC system installation including a Lennox 90,000 BTU high-efficiency furnace, 3-ton air conditioning unit with rear discharge configuration, programmable thermostat, and humidifier in basement mechanical room. Installed all necessary PVC condensate drain lines and combustion air intake/exhaust venting, connected refrigerant lines and electrical components, and integrated system with existing ductwork. Reconnected all utilities, verified proper operation of all equipment, and submitted permit applications for mechanical and electrical work to facilitate consumer energy rebate processing.

Completed comprehensive Gold AC inspection on an 11-year-old residential air conditioning system. Verified equipment operational status with homeowner and confirmed all components functioning properly. Outdoor condensing unit located against exterior brick wall in landscaped area with adequate clearance maintained. Performed standard preventive maintenance inspection including visual assessment of condenser unit condition, coil accessibility, and surrounding area. Unit positioned on concrete pad with appropriate mulched garden bed drainage. System operating as designed with no immediate service concerns identified at time of inspection.

Completed comprehensive Gold AC inspection on 8-year-old single-zone residential air conditioning system with air handler located in basement. Performed thorough evaluation of outdoor condensing unit positioned on rubber isolation pads with proper electrical disconnect and conduit installation. Inspected unit components including condenser coil, fan assembly with protective mesh guard, refrigerant lines, and electrical connections; verified all systems operational and equipment functioning properly at time of inspection.

Responded to recurring issue with generator priority box disabling air conditioning system on 3-year-old Briggs and Stratton 20kW natural gas generator with 150 amp automatic transfer switch. Inspected control board and relay components within priority management module, identified faulty relay causing improper load shedding sequence that was preventing AC operation. Removed defective controller unit for shop repair/replacement, documented existing installation specifications including transfer switch configuration with AC circuits and 220-volt modules. Upon controller replacement, will test automatic transfer switch operation, verify proper load prioritization sequence, and ensure AC system functions correctly during generator runtime.

Completed installation of 110K BTU furnace system in rear yard location with mechanical and electrical permits. Raised evaporator coil 4 inches and remeasured outlet transition to ensure proper clearances and airflow. Installed new thermostat, reconnected high velocity package system, and verified static pressure readings using digital manometer to confirm system operates within manufacturer specifications.

Completed Gold AC inspection on Carrier system with air handler located in basement. Replaced humidifier tube orifice as part of routine maintenance. Outdoor condenser unit exhibited heavy biological growth including moss and algae accumulation on coil fins and vertical supports, along with significant mineral deposits and debris buildup affecting heat transfer efficiency. Noted extensive rust staining on fan guard and top panel around motor hub, indicating prolonged moisture exposure. Condenser coils showed corrugation pattern with discoloration throughout and organic matter accumulation requiring attention. Unit operational at time of inspection with refrigerant lines properly secured to exterior wall. Recommended professional coil cleaning to restore optimal airflow and system efficiency due to heavy contamination of heat exchanger surfaces.

Provided estimate for replacement of R-22 air conditioning system and furnace, with primary focus on AC unit replacement. Assessed existing basement-installed HVAC equipment including furnace and cooling system with vertical ductwork extending to attic space. Evaluated current system configuration, drainage components including condensate pump, and electrical connections to determine replacement specifications for natural gas furnace and compatible air conditioning unit.

Conducted site evaluation for whole home generator replacement with Kohler brand equipment. Assessed existing generator installation location adjacent to building foundation, documenting current equipment positioning, conduit routing, and clearance requirements. Evaluated electrical service panel configuration and existing circuit breaker arrangement to determine integration requirements for new generator system. Photographed existing installation conditions including equipment access area, utility connections, and main electrical panel to develop accurate replacement specifications and ensure proper sizing for whole home backup power requirements.

Completed comprehensive Gold AC inspection on 9-year-old residential air conditioning system with basement-mounted air handler and coil. Performed full system evaluation of outdoor condenser unit, confirmed proper operation of fan assembly and protective grille, verified unit integrity with no visible damage or deterioration noted. Inspected condenser housing ventilation, assessed overall system condition, and documented equipment status through photographic documentation per maintenance protocol standards.

Responded to service request for gas lamp installation requiring experienced technician. Upon arrival, assessed existing gas line infrastructure and HVAC system components to determine proper connection points for new gas lamp fixtures. Installed gas solenoid valve assembly with appropriate male plug connections and switch wire configurations per manufacturer specifications. Routed gas supply lines from existing system, ensuring proper shut-off valve placement and leak-free connections using brass fittings. Completed all necessary electrical connections for ignition control, integrated wiring with existing outdoor lighting control board. Pressure tested all gas connections to verify system integrity and safe operation. All installations performed in accordance with local gas code requirements and safety standards.

Completed estimate for replacement of 27-year-old furnace unit located in basement utility room. Assessed existing beige furnace installation with connected galvanized plenum and ductwork system, noting copper refrigerant lines and flexible metal conduit. Documented significant condensation buildup on existing ductwork throughout mechanical space, indicating potential efficiency concerns with aging system. Photographed current HVAC configuration including duct connections, structural mounting, and proximity to water heater and utility systems to provide comprehensive replacement specifications.

Completed seasonal maintenance and tune-up on outdoor air conditioning condensing unit. Performed comprehensive inspection of unit components including fan motor, compressor, electrical connections, and refrigerant levels. Unit found in normal operating condition with no visible damage or wear, all systems functioning properly.

Performed comprehensive inspection and tune-up on Pabon brand outdoor condensing unit. Unit found in functional condition with fan assembly operating properly and protective grille intact. Verified proper placement on concrete pad, noted minor vegetation growth in surrounding gravel area that should be monitored to prevent airflow obstruction.

Completed mini split system installation over two-day period with full mechanical and electrical integration. Installed new dedicated electrical circuit with breaker panel modifications to support mini split system requirements, ensuring proper power supply and code compliance. All equipment mounted, leveled, and tested for proper operation with electrical connections verified and secured.

Completed installation of 5-ton air conditioning system with matching evaporator coil in left-position configuration. Installed new A/C unit with proper refrigerant connections, electrical hookup by licensed electrician, and integrated coil with existing furnace system. All ductwork connections secured, condensate drainage verified operational, and system tested for proper airflow and cooling performance upon startup.

Completed preventative maintenance tune-up on a 2-year-old residential HVAC system with indoor coil located in kitchen and Lennox outdoor condensing unit. Performed standard inspection protocol, verified equipment operational status, and documented system condition through photography. Unit found to be in clean, well-maintained condition with no visible defects or performance issues requiring immediate attention.

Provided estimate for complete HVAC system replacement in basement location, including air conditioning unit and natural gas furnace. Existing equipment is over 10 years old and non-operational. Assessment included evaluation of current Carrier furnace installation, electrical service panel capacity, condensate drainage system requiring sealing at connection points, and venting configuration to ensure proper system integration and code compliance for new equipment installation.

Completed scheduled maintenance on 10-year-old air conditioning system with outdoor condenser unit located in side yard and evaporator coil in basement. Performed comprehensive tune-up including inspection of refrigerant lines, electrical connections, and condenser fan operation. Retrieved furnace model number as requested and documented equipment specifications for service records.

Completed installation of a 40-gallon Bradford White tanked water heater with full reconnection of copper supply lines and brass fittings, including proper venting through metallic flue pipe. Additionally performed miscellaneous plumbing tasks including toilet removal and valve replacement to support the overall mechanical system upgrade.

Conducted on-site evaluation of existing gas water heater to assess code compliance and provide estimate for potential conversion to electric unit. Inspected current installation located in interior closet space, noting deteriorated surrounding conditions and aging infrastructure. Evaluated existing gas supply line configuration, venting system, and available electrical capacity to determine feasibility of converting from gas to electric water heater. Assessed clearance requirements, accessibility, and structural considerations for new electric unit installation. Documented current water heater specifications and installation conditions through photographic evidence. Provided homeowner with professional assessment regarding code compliance issues and outlined scope of work required for electric conversion, including new dedicated electrical circuit installation, removal of existing gas lines, and proper venting modifications.