Heating and Cooling Clinton Township

Completed comprehensive Gold AC Inspection on 10+ year old HVAC system located in basement. Unit was operational at time of service. Performed thorough examination of air handler components, including inspection of evaporator coil, copper refrigerant lines, electrical connections, and internal mechanical components. Assessed condition of heat exchanger fins, verified proper wiring connections, and examined ductwork connections including flexible duct transitions. System showing age-related wear consistent with equipment over 10 years old, but currently functioning as designed. All safety components and electrical connections verified during inspection.

Responded to no-cool call on 2-year-old AC system that stopped operating following recent Generac generator installation. Upon arrival, found both furnace and AC inoperative. Inspected electrical connections at generator transfer switch and discovered improper wiring configuration affecting HVAC system power supply. Verified generator transfer switch installation had interrupted proper electrical feed to heating and cooling equipment. Traced wiring from Generac control module through terminal blocks and confirmed multiple circuits were improperly configured on AC circuit distribution. Corrected electrical connections at transfer switch to restore proper power routing to HVAC systems. Verified proper voltage supply restored to both furnace and air conditioning unit. Cycled systems through startup sequence and confirmed both units operational. Performed requested AC tune-up including filter inspection, refrigerant charge verification, and airflow assessment. System now functioning proper

Performed system start-up on newly installed air conditioning unit with basement evaporator coil. Verified proper airflow through ductwork, confirmed all electrical connections at junction box, and tested refrigerant lines and condensate drainage system for proper operation.

Completed comprehensive tune-up on 10+ year old HVAC system including outdoor AC condenser unit and basement furnace. Performed thorough inspection of condenser unit showing age-related weathering and algae growth on exterior surfaces; verified proper operation of compressor, fan motor, and electrical disconnect. Conducted detailed furnace inspection with digital diagnostic testing equipment, measuring temperature differentials and system performance; inspected blower motor assembly, electrical connections, wiring harnesses, and internal mechanical components. Evaluated thermostat operation, humidifier functionality, and hot water tank condition as part of complete system assessment. All equipment found operating within normal parameters with no immediate safety concerns identified; unit shows typical wear consistent with age but remains functional.

Responded to a toilet malfunction that had been occurring for two days in a single bathroom area. Performed a complete rebuild of the toilet tank assembly, including replacement of all internal components: flush valve, fill valve, float mechanism, and flapper. The existing components showed significant mineral deposits and rust staining throughout the tank interior, indicating deteriorated seals and compromised flushing performance. Successfully restored proper toilet function and water flow control.

Completed installation and reconnection of a 40-gallon Bradford White power vent water heater in basement utility area. Installed copper supply piping with brass fittings and isolation valves, connected power vent exhaust system, and verified all connections for proper operation. Unit tested and operational upon completion.

Completed Gold AC inspection on residential single-unit air conditioning system with equipment age exceeding 10 years. Inspected outdoor condensing unit with operational fan assembly and protective grille, verifying proper function and clearance from debris. Air handler/coil located in basement confirmed. Documented significant rust corrosion present throughout electrical disconnect box enclosure, including deterioration around interior panel edges, cable entry points, and mounting surfaces indicating prolonged moisture exposure requiring attention. Unit operational at time of inspection with weather conditions suitable for accurate assessment.

Responded to service call regarding damaged thermostat wiring in heating system. Upon inspection, located cut thermostat wire connected to zone control modules in multi-zone hydronic heating system. Assessed the control panel configuration with multiple zone valves and verified extent of wire damage. Documented existing conditions of copper piping network, zone control boxes with visible blue and red wiring connections, and overall system layout for repair planning and future reference.

Completed comprehensive Gold AC inspection on residential split system with air handler located in basement and outdoor condenser unit. Inspected triangular air filter showing moderate dust accumulation with pleated media intact and functional. Evaluated outdoor condenser unit positioned near building foundation, noting significant debris accumulation including dried vegetation, straw, and organic matter surrounding unit requiring cleanup for optimal airflow and system efficiency. Documented equipment condition through photographic inspection, verified operational status of approximately 20-year-old system, and assessed accessibility of components for future maintenance requirements.

Responded to no-cooling complaint on 6-year-old Daikin split system. Performed diagnostic evaluation and determined condenser unit was not receiving power due to faulty contactor. Replaced defective contactor, verified proper voltage at disconnect, and tested system operation. Unit now cooling properly with condenser fan and compressor running within normal parameters.

Completed comprehensive cooling maintenance tune-up on 3-year-old Lennox HVAC system, including inspection of evaporator coil, condensate management, and GeneralAire humidifier integration. All components operating within manufacturer specifications with proper refrigerant levels and airflow confirmed. System showed normal condensation patterns and all safety controls tested satisfactorily.

Completed comprehensive Gold AC inspection on 2019 residential air conditioning system with air handler located in basement and condenser unit positioned on exterior concrete pad. Performed thorough multi-point inspection including evaluation of outdoor condenser unit with operational fan motor and protective wire guard, verified proper placement and clearance around unit, assessed condensate drain line routing, and documented equipment condition through photographic records. System found to be in proper working order with no immediate service requirements identified.

Completed diagnostic evaluation and provided replacement estimate for aging R22 air conditioning system experiencing inadequate airflow and insufficient cooling capacity. Assessed existing unit located in interior utility closet near bathroom, documented electrical panel configuration and current HVAC installation within louvered cabinet enclosure. Recommended full system replacement due to obsolete refrigerant type and equipment age affecting performance.

Completed comprehensive Gold AC inspection on 12-year-old air conditioning system with basement-located air handler and coil. Performed thorough examination of outdoor condenser unit including fan assembly, blade condition, and housing integrity; noted normal weathering consistent with outdoor exposure and minor debris accumulation around unit perimeter. All equipment confirmed operational prior to inspection, with system components functioning within normal parameters for unit age.

Performed air conditioning system startup on Lennox outdoor condensing unit. Contacted customer 30 minutes prior to arrival as requested, then completed full system commissioning including temperature verification readings and operational testing to confirm proper system performance.

Completed comprehensive AC tune-up and inspection on 20-year-old outdoor condensing unit. Performed standard maintenance protocol including system performance evaluation, electrical testing, refrigerant level assessment, and condenser coil inspection. Noted vegetation encroachment requiring clearance and debris accumulation around unit base that may restrict airflow; customer advised of recommended clearance maintenance for optimal system efficiency and longevity.

Completed on-site assessment for Magic Pack heating and cooling unit replacement in owner-occupied apartment with balcony-mounted equipment of unknown age. Documented existing HVAC system configuration, including interior utility space connections, ductwork layout, water heater proximity, gas line routing, and electrical panel location. Provided comprehensive replacement quote based on current equipment condition and installation requirements.

Completed Gold Furnace Inspection on 20+ year old outdoor furnace unit located behind condo. Performed comprehensive system evaluation including burner operation check, electrical connections inspection, and blower motor assessment. Verified proper ignition with burners displaying characteristic blue flame pattern indicating efficient combustion. Inspected control module wiring, blower assembly, and all electrical components. System operational at time of inspection. Documentation photos captured for service records.

Responded to water leak complaint originating from a recently completed installation. Upon inspection, identified active leak at T-union connection in copper piping located in ceiling space. Accessed mechanical chase and attic area to assess copper plumbing lines and verify source of water intrusion. Documented existing conditions including copper pipe routing, insulation placement, and surrounding mechanical systems. Coordinated with installation team to review original connection methods and determine corrective action required for proper seal at union fitting.

Responded to service call for 2005 furnace experiencing fan operation without heat production and chronic overheating issues due to oversized equipment. Performed diagnostic evaluation of basement-installed furnace system, assessed ductwork configuration and equipment sizing relative to heating load requirements. Documented existing system conditions including furnace cabinet, supply plenum measurements, and overall installation setup. Provided comprehensive replacement estimate addressing proper equipment sizing to eliminate overheating cycles and restore reliable heating operation to the residence.