Heating and Cooling Ferndale

Performed plumbing estimate for gas line assessment in basement of 60+ year old home requiring correction or update for new dryer installation. Inspected existing gas piping configuration, which was suspected to be improperly sized or routed for dryer connection. Evaluated copper gas lines, shutoff valves, and existing mechanical connections in utility area. Documented current piping layout and identified necessary modifications to bring gas supply up to code for safe dryer operation. Provided recommendations for proper gas line sizing, routing, and installation to meet current building codes and manufacturer specifications.

Completed preventative maintenance tune-up on 7-year-old residential air conditioning system located in basement. Performed comprehensive inspection of condensing unit, verified proper operation of outdoor fan assembly, checked refrigerant charge levels and subcooling temperatures per manufacturer specifications for R-410A system, cleaned condenser coil, inspected electrical connections and components, and confirmed unit is operating within normal parameters for optimal cooling performance.

Returned to site to continue compressor diagnostics on outdoor HVAC unit. Performed electrical testing using digital multimeter and clamp meter to measure voltage and amperage at the condensing unit. Readings indicated 62.1 amps with voltage measurements taken at multiple points in the system. Inspected wiring harnesses, refrigerant line connections, and conduit routing. Documented findings with photos for further analysis and determination of compressor viability.

Completed full HVAC system replacement including installation of 70,000 BTU Lennox furnace, 2.5 ton air conditioning unit positioned in right side yard, Ecobee 3 Lite thermostat, humidifier, and condensate pump. All PVC venting and drain lines properly installed with secure connections, flexible ductwork routed and connected to new furnace, and existing water heater reconnected to system. Mechanical and electrical permits obtained prior to installation, all components tested and verified operational upon completion.

Reinstalled electrical circuit box on exterior brick wall following storm damage. Ran new conduit lines from circuit box to service connector using flexible metal armored cable, securing all connections per code requirements. Restored proper electrical service configuration with all components properly mounted and grounded.

Conducted comprehensive full system HVAC evaluation for central air conditioning installation. Assessed existing ductwork configuration in mechanical space, documenting current infrastructure including insulated metal ductwork with multiple horizontal and vertical runs. Measured and marked critical dimensions on existing ducts for proper equipment sizing and integration planning. Evaluated air handler location and structural support requirements, noting existing mounting provisions and spatial constraints for new equipment installation. Provided complete system replacement estimate including central air conditioning unit specifications compatible with existing duct infrastructure.

Responded to service call for central air conditioning system evaluation. Upon arrival, conducted comprehensive equipment assessment in basement utility area where HVAC system is located. Documented existing conditions including ceiling damage in mechanical space and current installation configuration of ductwork and equipment components. System confirmed operational for both heating and cooling functions at time of inspection. Provided estimate recommendations for equipment replacement options based on assessment findings.

Inspected gas line connection to dryer in basement area to verify proper installation, secure fittings, and absence of leaks. Replaced damaged dryer vent that had split in half with new venting system, ensuring proper routing through crawl space and secure connections to prevent lint buildup and maintain safe exhaust flow. All gas connections tested and confirmed operational with no leaks detected.

Completed sump pump installation and gas line re-piping in unfinished basement utility area. Installed new PVC drainage piping with appropriate fittings, valves, and connections to ensure proper sump pump discharge. Re-routed gas piping system using code-compliant materials and securing methods along ceiling joists and wall structures to improve safety and functionality of the existing gas distribution system.

Provided replacement estimates for air conditioning system and natural gas furnace located in basement. Current 10+ year old equipment is operational but nearing end of service life. Evaluated existing outdoor condenser unit showing signs of age and debris accumulation, along with older thermostat system, and presented options for complete HVAC system replacement.

Provided comprehensive estimate for complete HVAC system replacement in basement location, including 38-year-old non-functional air conditioning unit from 1986 and 18-year-old natural gas furnace currently operational. Assessed existing equipment configuration, ductwork accessibility, electrical requirements, and structural considerations for new system installation in basement mechanical room with adequate clearances for service access.

Performed sewer line camera inspection to assess condition and identify any obstructions or damage. Video inspection revealed the interior condition of the main sewer line, allowing for accurate diagnosis and estimate preparation for any necessary repairs or cleaning services.

Completed estimate for new air conditioning system installation at residence with no existing AC unit. Customer requested outdoor condenser placement on rear side of property. Assessed basement utility area with existing ductwork infrastructure, evaluated electrical panel location and capacity for new system integration. Photographed installation site including current HVAC ductwork configuration, structural supports, and available space for equipment placement. Provided comprehensive estimate for complete AC system installation including outdoor condenser unit, indoor air handler or evaporator coil integration with existing ductwork, refrigerant line set, electrical connections, condensate drainage, and thermostat wiring.

Completed comprehensive Gold AC Inspection on a 6-year-old Daikin mini-split system with outdoor condenser unit located at grade level and air handler positioned in basement. Performed multi-point inspection protocol including visual assessment of condenser unit housing, fan assembly operation, refrigerant line connections, electrical components, and overall system functionality. Unit found to be in proper working condition with no immediate service requirements identified at time of inspection.

Completed comprehensive Gold Furnace Inspection on recently installed gas furnace unit located in laundry room. Performed full tune-up service including inspection of blower motor assembly, electronic ignition system, control board connections, and all electrical wiring connections. Verified proper operation of all internal components, checked transformer function, and inspected PVC venting system. All components found to be in normal operational condition with no deficiencies noted. Unit operating within manufacturer specifications.

Performed comprehensive AC tune-up and inspection on 15-year-old residential air conditioning unit located in basement. Conducted refrigerant system diagnostics using digital multimeter and pressure testing equipment at outdoor condensing unit, checking service ports and electrical components. System evaluated for proper operation with capacitance readings taken and all mechanical components assessed for wear and functionality.

Completed full HVAC system installation including removal of existing lowboy furnace and installation of new 70,000 BTU furnace, 2-ton air conditioning unit with rear discharge configuration, programmable thermostat, humidifier, and furnace liner. Performed all mechanical and electrical connections, verified proper refrigerant charge and system pressures using manifold gauges showing appropriate subcooling readings, reconnected existing condensate pump, and confirmed all equipment operational per manufacturer specifications.

Responded to service call for toilet that would not drain and was overflowing. Upon inspection, removed tank lid to diagnose drainage issue and assessed internal flush mechanisms and components. Addressed the blockage causing the overflow condition, restored proper drainage function, and verified toilet was operating correctly with no further overflow issues.

Conducted comprehensive site assessment for full HVAC system replacement in residential property. Evaluated existing aging furnace unit and ductwork infrastructure currently installed in basement mechanical room. Documented current system configuration including beige cabinet-style furnace with visible wear, discoloration, and outdated components. Assessed galvanized metal ductwork showing significant rust staining, corrosion, and age-related deterioration throughout distribution system. Photographed equipment layout, plenum connections, and surrounding mechanical space to develop accurate replacement specifications. Evaluated structural constraints, clearances, and accessibility for new furnace installation and addition of central air conditioning system. Identified necessary modifications to existing duct system to accommodate AC integration. Provided detailed estimate for complete system replacement including new high-efficiency furnace, central air conditioning unit, and any requir

Completed comprehensive Gold AC Inspection on a 5-year-old outdoor condenser unit. Performed full system evaluation including inspection of condenser coils, fan motor operation, refrigerant levels, electrical connections, and capacitor function. Cleaned debris from unit exterior and surrounding area, verified proper airflow through condenser coils, and confirmed system is operating within normal parameters for optimal cooling performance.