Heating and Cooling Hazel Park

Performed comprehensive tune-up and inspection on Navien tankless water heater located in utility room. Unit was operational upon arrival with display reading 42°F. Removed front access panel and conducted thorough internal inspection of all major components including primary and secondary heat exchangers, gas valve assembly, control board, and digital interface module. Verified proper operation of combustion system, checked all electrical connections and wiring harnesses, inspected heat exchanger surfaces for scale buildup or corrosion, and examined condensate drain system. Tested water flow sensors, temperature sensors, and safety controls for proper function. Inspected all copper and PVC supply and return piping, brass fittings, and isolation valves for leaks or deterioration. Verified proper venting connections and checked exhaust system integrity. System operating within normal parameters at time of service completion.

Responded to no heat call on HVAC system less than 10 years old located in basement. Upon arrival, inspected furnace and found control board with loose wire connections at the terminal block. Secured all electrical connections, tested thermostat communication, and verified proper 24V power supply to control circuit. Cycled system through heating mode and confirmed ignition sequence, burner operation, and blower activation functioning properly. Unit restored to normal heating operation.

Disconnected water supply lines for dishwasher and refrigerator, and gas line for stove to facilitate flooring installation in kitchen area. Secured dishwasher mounting bracket to cabinet base using appropriate hardware. Reconnected all appliance lines upon completion of flooring work, verified proper connections and tested for leaks at all connection points.

Responded to service call for furnace pilot relight in crawl space location. Conducted diagnostic assessment of aging furnace system and evaluated equipment condition and accessibility constraints. Provided comprehensive replacement estimate due to equipment age and crawl space installation challenges, documenting existing infrastructure and access points for future installation planning.

Responded to no heat call for furnace located in crawl space. Upon arrival, found pilot light extinguished on gas furnace. Inspected unit and verified gas supply, thermocouple condition, and pilot assembly functionality. Successfully relit pilot light and confirmed proper ignition sequence and burner operation. Observed evidence of moisture accumulation on adjacent ductwork and mechanical components in crawl space environment. Verified furnace cycling properly with adequate airflow and proper combustion. System restored to normal heating operation.

Completed preventive maintenance tune-up on gas-fired HVAC system located in attic space. Accessed equipment via ladder and performed comprehensive inspection of heating unit. Verified proper ignition and burner operation with all burners firing correctly and displaying characteristic blue-purple flame pattern. Inspected return air grille and filter access point at ceiling level. Checked electrical connections and wiring throughout system, confirming secure connections and proper voltage. Examined gas conversion components and fuel delivery system for proper configuration. Verified all safety controls and limit switches functioning within manufacturer specifications. System operating efficiently with no deficiencies noted at time of service.

Completed comprehensive tune-up and safety inspection on 10+ year old HVAC system located in basement. Performed thorough examination of evaporator coil assembly, inspecting for proper airflow and refrigerant circuit integrity. Evaluated flame sensor condition, noting oxidation buildup on probe surface which was documented for monitoring. All safety controls tested and verified operational, system confirmed functioning properly at time of service.

Completed comprehensive tune-up on gas furnace located in basement. Inspected burner assembly and confirmed proper ignition with all three burners firing cleanly with blue flames. Examined heat exchanger, gas supply lines, and electrical connections for proper operation. Cleaned and tested all safety controls and verified proper system operation upon completion.

Completed mechanical-only installation of a 50-gallon short Bradford White tanked water heater in utility room. Reconnected all water supply lines using copper piping with proper fittings, installed black insulated hot water distribution lines, and configured cold water inlet connections. Secured all piping runs with appropriate straps and hangers, ensured proper clearances per manufacturer specifications, and verified all connections for leak-free operation. Unit was positioned on existing floor surface with adequate ventilation access and proper venting configuration maintained through existing ductwork system.

Responded to emergency water leak call for leaking water heater. Upon arrival, immediately shut off water supply to prevent further water damage. Inspected 50-gallon water heater and confirmed active leak requiring unit replacement. Documented existing equipment configuration including water heater installation, connected plumbing lines, and adjacent HVAC furnace system. Photographed mechanical room setup showing water heater condition, copper and black supply/discharge piping, ductwork assembly, and overall utility space layout. Provided estimate for replacement with new 50-gallon short water heater. Customer advised of findings and replacement options.

Completed Gold AC inspection on residential split system with air handler located in basement. Performed comprehensive maintenance including inspection of outdoor condensing unit, verified proper operation of compressor and condenser fan motor, checked refrigerant levels and system pressures, cleaned condenser coils, inspected electrical connections and contactors, and evaluated overall system performance. Unit found operating within normal parameters with no immediate service concerns identified.

Responded to service call for 12-year-old Rheem Performance 40-gallon natural gas water heater located in utility room with reported venting issues. Upon inspection, diagnosed improper venting preventing safe exhaust of combustion gases. Completed installation of new tanked water heater system, including proper venting configuration to ensure adequate draft and combustion air flow. Connected supply lines with flexible braided hoses, installed temperature and pressure relief valve, and verified all gas connections for leak-free operation. System tested and operational upon completion.

Completed routine AC inspection on 4-year-old residential condensing unit. System operational with all components functioning within normal parameters. Inspected electrical compartment, verified capacitor connections and wiring integrity, and confirmed proper outdoor unit operation.

Completed comprehensive Gold AC Inspection and tune-up on residential air conditioning system under plan membership. Performed full system evaluation including condenser unit inspection, verified operational status of all components, and documented unit condition with photos. Noted vegetation overgrowth around outdoor condenser unit requiring future clearance to maintain optimal airflow and system efficiency.

Completed comprehensive estimate inspection for furnace and air conditioning system replacement. Identified critical deficiencies including undersized return air duct system on existing furnace installation and improper equipment placement in utility room. Documented aged air conditioning unit requiring replacement. Assessed ductwork showing deterioration with visible tape repairs, inadequate insulation, and structural concerns in crawlspace area. Noted compromised building envelope with damaged drywall, exposed insulation, and flooring deterioration affecting system performance. Provided recommendations for proper furnace installation with correctly sized return air system, complete air conditioning replacement, and correction of existing installation deficiencies to meet code requirements and manufacturer specifications.

Performed seasonal tune-up and combustion analysis on 1-year-old natural gas furnace located in utility room. Combustion testing revealed optimal performance with oxygen levels at 4.7%, carbon monoxide at 23 ppm, carbon dioxide at 9.2%, and combustion efficiency at 100.0% with stack temperature of 64°F. All equipment operating within manufacturer specifications with no deficiencies noted.

Responded to service call for Rheem Performance gas water heater with pilot light extinguishing on a recurring three-week cycle. Performed diagnostic inspection of the unit located in utility closet adjacent to laundry appliances. Examined thermocouple, gas control valve, pilot assembly, and venting system to identify cause of intermittent pilot failure. Documented equipment condition and configuration with photographic evidence for service records.

Responded to service request for sump pump evaluation and same-day installation following initial electrical assessment. Upon arrival, inspected existing sump pump system and found severe corrosion throughout the unit, including extensive rust damage to the pump housing, motor assembly, and discharge piping. The pump basin exhibited significant rust staining on interior walls with degraded protective coating. Water in the pit appeared dark and sediment-laden, indicating compromised pump performance. Provided comprehensive estimate for complete sump pump replacement, including removal of failed corroded unit and installation of new pump system with appropriate discharge piping and electrical connections. Customer accepted estimate and authorized same-day installation. Removed deteriorated pump assembly and cleaned sump basin of accumulated sediment and debris. Installed new sump pump with check valve, ensuring proper float operation and discharge routing. Tested system operation throug

Performed system start-up on Goodman packaged heating and cooling combo unit installed on concrete pad adjacent to residential structure. Verified proper operation of all components, checked refrigerant line connections at building penetration, and confirmed electrical connections at exterior meter location. Unit operational and performing to manufacturer specifications.

Responded to service call for circuit breaker tripping issue. Performed diagnostic inspection of electrical system and identified sump pump circuit as source of nuisance tripping. Inspected sump pump electrical connections in basement utility area, verified proper grounding, and tested circuit integrity. Resolved tripping condition and confirmed all electrical components operating safely within normal parameters.