Heating and Cooling Hazel Park

Performed seasonal tune-up and combustion analysis on 1-year-old natural gas furnace located in utility room. Combustion testing revealed optimal performance with oxygen levels at 4.7%, carbon monoxide at 23 ppm, carbon dioxide at 9.2%, and combustion efficiency at 100.0% with stack temperature of 64°F. All equipment operating within manufacturer specifications with no deficiencies noted.

Responded to service call for Rheem Performance gas water heater with pilot light extinguishing on a recurring three-week cycle. Performed diagnostic inspection of the unit located in utility closet adjacent to laundry appliances. Examined thermocouple, gas control valve, pilot assembly, and venting system to identify cause of intermittent pilot failure. Documented equipment condition and configuration with photographic evidence for service records.

Responded to service request for sump pump evaluation and same-day installation following initial electrical assessment. Upon arrival, inspected existing sump pump system and found severe corrosion throughout the unit, including extensive rust damage to the pump housing, motor assembly, and discharge piping. The pump basin exhibited significant rust staining on interior walls with degraded protective coating. Water in the pit appeared dark and sediment-laden, indicating compromised pump performance. Provided comprehensive estimate for complete sump pump replacement, including removal of failed corroded unit and installation of new pump system with appropriate discharge piping and electrical connections. Customer accepted estimate and authorized same-day installation. Removed deteriorated pump assembly and cleaned sump basin of accumulated sediment and debris. Installed new sump pump with check valve, ensuring proper float operation and discharge routing. Tested system operation throug

Performed system start-up on Goodman packaged heating and cooling combo unit installed on concrete pad adjacent to residential structure. Verified proper operation of all components, checked refrigerant line connections at building penetration, and confirmed electrical connections at exterior meter location. Unit operational and performing to manufacturer specifications.

Responded to service call for circuit breaker tripping issue. Performed diagnostic inspection of electrical system and identified sump pump circuit as source of nuisance tripping. Inspected sump pump electrical connections in basement utility area, verified proper grounding, and tested circuit integrity. Resolved tripping condition and confirmed all electrical components operating safely within normal parameters.

Responded to complaint of burning smell originating from tanked water heater in first-floor kitchen utility closet. Upon arrival, conducted thorough inspection of water heater unit and surrounding mechanical equipment including adjacent furnace system. Examined water heater exterior, connections, venting system, and associated copper piping for signs of overheating, electrical issues, or mechanical failure. Inspected flue pipe configuration and draft hood assembly for proper venting and potential backdraft conditions. Verified gas connections, burner assembly access, and surrounding insulation materials for heat damage or deterioration. Documented equipment condition with photographs showing water heater placement in compact closet space alongside HVAC equipment. No immediate safety hazards identified requiring emergency shutdown during inspection period.

Responded to non-functional garbage disposal in first-floor kitchen sink of 1950s-era home. Upon inspection, found existing black garbage disposal unit mounted under sink with standard drain configuration and P-trap assembly. Assessed unit for electrical connectivity, mechanical jamming, and reset functionality. Disposal showed signs of age and wear consistent with original installation timeline. Restored unit to working condition through troubleshooting and repair procedures. Verified proper drainage, mounting security, and operational performance before completion.

Performed a second opinion assessment on a 25-year-old natural gas furnace located in the utility room. Visual inspection revealed excessive dust accumulation throughout the system components and electrical connections, confirming the previously diagnosed cracked heat exchanger. Documented findings with detailed photographs of the deteriorated heat exchanger and surrounding components.

Completed Gold Furnace Inspection on a 4-year-old unit located in basement. Removed access panel to inspect interior components including blower motor assembly, electrical connections, control module, and circuit board. All components functioning properly with no issues identified.

Conducted AC replacement estimate at residential property with limited access via narrow concrete walkway along brick exterior. Inspected existing HVAC system located in utility space, noting current installation configuration including PVC drainage, copper refrigerant lines, and electrical connections. Photos documented both external access constraints and internal system components for accurate replacement planning.

Conducted comprehensive assessment of 24-year-old furnace and AC system located in basement. Visual inspection confirmed customer's report of multiple issues, including suspected cracked heat exchanger. Documented existing installation configuration, including ductwork condition and electrical connections, to prepare detailed replacement estimate through Michigan Saves program as requested.

Inspected 20+ year old natural gas furnace located in crawl space under house; unit is currently operational but approaching end of service life. Exterior assessment revealed weathered York AC unit with significant rust on fan cover, dirt/residue buildup on coil cover, and deteriorated condition consistent with age. Provided replacement options for complete system upgrade to improve efficiency and reliability.

Performed Gold Furnace Inspection on a 1-year-old forced air system located in the basement. Inspected Bradford White "Defender" water heater system, confirming proper ventilation through galvanized metal ducting and verifying all plumbing connections were secure. Used hex key tool for minor adjustments during the inspection process.

Conducted a site assessment for new whole home generator installation. Evaluated the existing electrical panel located in the basement, which shows adequate space for generator integration. Inspected current HVAC system placement and utility area configuration to determine optimal generator positioning and connection requirements.

Diagnosed intermittent heating failure on Emerson thermostat-controlled system that was shutting down during windy conditions. Inspected furnace installation and ductwork in basement, finding proper component installation with no visible damage. Resolved issue by adjusting thermostat programming and verifying system operation through complete heating cycle.