Expert Heating and Cooling Services in Madison Heights, MI

Responded to reported gas leak at furnace following recent AC installation and furnace relocation. Performed comprehensive gas leak detection and pressure testing on all gas lines serving the Trane furnace and A.O. Smith water heater. Inspected all gas line connections, fittings, and the gas valve assembly at the furnace location. Utilized leak detection solution and electronic gas detection equipment to test all joints, unions, and threaded connections throughout the system. Verified proper gas pressure at appliances and confirmed integrity of flexible gas connectors and black iron piping. All connections tested leak-free with no detectable gas escape at furnace supply line, water heater connections, or associated fittings. System deemed safe for continued operation with no corrective action required.

Completed full HVAC system installation including 70,000 BTU furnace with liner and humidifier, 2-ton air conditioning unit with rear discharge configuration, and condensate pump. Coordinated with licensed electrician for all required electrical connections and panel work. Mechanical and electrical permits were obtained prior to installation, and all equipment was properly mounted, connected, and tested for optimal performance.

Completed comprehensive Gold Plan maintenance inspection on 11-year-old Bryant furnace located in basement. Performed full system evaluation including burner assembly inspection, heat exchanger examination, blower motor operation check, gas valve testing, and electrical connection verification. Inspected pleated air filter showing dust accumulation; documented current condition with photos of filter media and internal components including ignition system, control board, and condensate drainage. All mechanical and electrical systems operating within normal parameters. Unit functioning properly with no immediate safety concerns identified.

Completed comprehensive tune-up and inspection on 10+ year old HVAC system including basement-installed gas furnace and outdoor air conditioning condenser unit. Performed thorough examination of furnace interior components including blower motor assembly, gas valve connections, electrical control board, and all associated wiring harnesses. Verified proper operation of all safety controls and electrical connections throughout the system. Inspected outdoor condenser unit positioned on concrete pad adjacent to building foundation, checking refrigerant lines, electrical disconnect, conduit connections, and fan operation. Confirmed adequate clearance around outdoor unit and verified secure mounting on concrete slab. All components found to be functioning within normal operating parameters with organized wiring and proper installations maintained throughout both heating and cooling systems.

Completed full HVAC system installation including 70,000 BTU furnace, 2-ton air conditioning unit with rear discharge configuration, Ecobee 3 Lite thermostat, humidifier, condensate pump, and low-profile drain pan kit. Coordinated electrical work for new dedicated circuit installation to meet code requirements. Obtained mechanical and electrical permits, performed system remeasure, and ensured proper setup for utility rebate qualification.

Responded to service call for AC unit leaking inside the house with a 10-year-old system located in the basement. Upon inspection, discovered the system had low refrigerant charge and identified a cracked eyelet on the heat exchanger. Documented existing electrical panel configuration and outdoor condenser unit condition with photographs for estimate purposes.

Responded to water leak complaint on 10-year-old air conditioning unit in basement. Upon inspection, discovered significant water staining and discoloration around the evaporator coil area, indicating prolonged moisture exposure. Found primary condensate drain line completely obstructed, causing water to back up and overflow into the living space. Observed corrosion and rust accumulation at the base of the air handler cabinet, consistent with chronic drainage issues. Cleared condensate drain blockage using appropriate tools and verified proper drainage flow. Flushed drain line with cleaning solution to remove biological buildup and debris. Inspected drain pan for cracks or damage; pan structurally sound but showed evidence of standing water. Tested system operation and confirmed condensate draining properly through primary drain line. Advised ongoing maintenance of condensate system to prevent future blockages. Photographed affected areas showing water damage to insulation and corrosio

Completed installation of a 14kW Generac standby generator system, model 22072580, including all required electrical connections and gas line integration. Secured necessary mechanical, electrical, and generator permits prior to installation. System tested and verified operational with proper pressure readings confirmed on gas supply line.

Responded to service call for water heater with pilot light that would not ignite. Upon arrival, inspected Whirlpool tanked water heater unit located in basement utility area alongside HVAC equipment. Performed diagnostic assessment of pilot assembly, thermocouple, and gas supply line. Tested gas valve operation and verified proper venting through existing exhaust system. Cleaned pilot orifice and burner assembly to ensure proper flame characteristics. Checked all copper supply line connections and fittings at top of unit for integrity. Successfully relit pilot light and verified sustained ignition. Tested main burner operation through full heating cycle to confirm proper function. Inspected surrounding area and confirmed adequate clearances per manufacturer specifications. Unit restored to full operational status with pilot remaining lit and burner cycling appropriately.

Responded to no cooling complaint with unit running but no airflow throughout system. Upon inspection, found severely restricted return air filter causing complete blockage of airflow to air handler. Removed and replaced dirty air filter with new filter, restoring proper airflow to system. Verified system operation with adequate airflow at all registers and proper cooling function restored.

Completed Gold AC Inspection on a 7-year-old split system with outdoor condenser unit located in backyard and air handler in basement. Performed comprehensive maintenance inspection of outdoor unit, which showed normal weathering and proper electrical connections with no visible damage or operational concerns. All equipment confirmed operational prior to inspection, and technician accommodated customer's driveway access request.

Responded to water leak complaint on 13-year-old air conditioning system located in basement. Upon inspection, found condensate drain system with significant buildup and blockage causing water to overflow onto basement floor. Cleared clogged condensate drain line and cleaned heavily stained condensate trap, which showed extensive brown residue accumulation from prolonged use. Inspected blower motor assembly and electrical connections within air handler unit to ensure proper operation. Verified condensate drainage flowing freely after clearing blockage. System tested and operating properly with no further water leakage observed.

Responded to service call for water leakage from 10-year-old air handler unit located in basement. Upon inspection, identified active leak at side of unit following previous condenser repair. System operates on R22 refrigerant and showed signs of low refrigerant charge. Documented equipment condition with photographic evidence showing air handler installation, ductwork connections, and exterior condensing unit positioned against building exterior. Provided estimate for complete HVAC system replacement due to age of equipment, refrigerant type, and recurring issues with both indoor and outdoor components.

Conducted on-site assessment for heating and cooling system replacement at a small residential property (0-1500 sq.ft.). Evaluated existing natural gas furnace located in interior closet and assessed ductwork configuration, noting measurements and clearances for replacement equipment. Inspected exterior condenser location and electrical conduit routing along building exterior to determine installation requirements for new HVAC system.

Responded to water leak complaint on 10-year-old air handler unit located in basement. Upon inspection, discovered water leaking from side of air handler cabinet, which developed following recent condenser unit repair. Identified clogged condensate drain line as primary cause of water accumulation and leakage. Cleared drain line blockage using appropriate tools and verified proper drainage flow. Inspected condensate pump operation and confirmed functional status. Checked drain pan for cracks or damage and found pan intact. Verified air handler cabinet seals and connections for proper installation. System tested and confirmed no further water leakage present at time of departure.

Coordinated with city utilities for water main shutoff to facilitate meter repairs and toilet installation. Replaced deteriorated floor drain assembly showing extensive corrosion and surrounding floor damage with broken tile and concrete fragments. Addressed water-damaged areas around drain perimeter exhibiting brown discoloration and structural deterioration. Completed toilet installation and restored water service following meter repair work. All plumbing connections tested and verified operational upon completion.

Completed full HVAC system installation including a 70,000 BTU Lennox furnace and 1.5-ton Lennox air conditioning unit with rear discharge configuration. Installed furnace in interior utility closet with proper venting, exhaust flue, condensate drainage system using PVC piping, and electrical connections including control wiring and disconnect. Mounted AC condensing unit on rubber isolation pad against exterior wall with appropriate clearances, installed electrical disconnect box, and completed refrigerant line connections. System installation included condensate pump, drain pan with wet switch safety device, and complete line set flush prior to charging. Requested and coordinated mechanical and electrical permits for the installation. Reconnected all electrical components to code specifications. Performed complete system startup, verified proper operation of both heating and cooling cycles, and confirmed all safety devices functioning correctly.

Removed and disposed of existing toilet that had been disconnected and unused for several years in upstairs bathroom of 1953-era home. Installed customer-supplied replacement toilet, including new wax ring, closet bolts, and water supply connection. Verified proper sealing, functionality, and absence of leaks upon completion.

Completed estimate for replacement of 23-year-old R22 cooling system and furnace located on first floor after air conditioning failure. Assessed existing HVAC installation including vertical ductwork, gas lines, and thermostat controls, documenting equipment condition and configuration for full system replacement proposal.

Responded to no cooling complaint on 10+ year old first floor air conditioning system. Upon arrival, performed electrical diagnostics on outdoor condensing unit using clamp meter to measure amperage draw and verify compressor operation. Unit evaluated and electrical measurements recorded to determine system performance and identify cause of cooling failure.