Local Heating and Cooling Services in Roseville, MI

Completed comprehensive Gold-level furnace inspection on 2019 forced-air heating system located in basement. Performed thorough examination of furnace unit, ductwork connections, and integrated humidification system. Verified all mechanical components operating properly, inspected flex duct connections and PVC condensate drainage, checked electrical connections and safety controls, and confirmed humidifier function with proper water supply connections. All equipment found in good working condition with no immediate service needs identified.

Responded to service call for 35-40 year old hot water boiler located in basement that failed to provide adequate heating during previous winter season. Performed comprehensive system inspection and diagnostic evaluation to assess operational status and identify potential repair needs. Documented equipment condition with photographic evidence for service records and repair recommendations.

Completed sump pump installation at commercial loading dock facility experiencing significant water accumulation. Installed new sump pump system in concrete basin with deteriorated walls showing extensive water damage and rust staining. Routed discharge line through flooded area to manage standing water conditions throughout the loading bay and warehouse space.

Responded to service call for non-functioning light fixtures in commercial warehouse facility. Performed diagnostic assessment of fluorescent lighting system mounted on high ceiling truss framework. Identified and resolved electrical issues affecting multiple overhead fixtures, restoring proper illumination throughout the warehouse storage and distribution area.

Completed comprehensive Gold Furnace Inspection on 25-year-old heating system located in basement. Performed thorough examination of all internal components including pressure switch, draft inducer motor assembly, gas valve, burner manifold, electrical connections, and safety controls. Documented equipment condition with photographs showing operational status of multi-unit system, verified proper wiring connections throughout, and confirmed all components are functioning within normal parameters for unit age.

Completed comprehensive Gold-level furnace inspection on 12-year-old Bryant furnace unit located in basement. Performed full system diagnostic including visual inspection of heat exchanger, burner assembly, ignition system, and all safety controls. Verified proper operation of White-Rodgers programmable thermostat, checked temperature differential, and confirmed heating cycle functionality. Inspected all gas connections, flue piping, and condensate drainage system for proper operation and safety compliance. All components found operating within manufacturer specifications with no immediate service needs identified.

Completed scheduled maintenance on a 1-year-old residential furnace located in the basement. Performed comprehensive system inspection including verification of burner operation with blue flame combustion visible through observation port. Inspected all internal components, gas valves, piping connections, electrical wiring, and safety controls for proper operation. Evaluated and documented condition of air filter showing accumulated debris; filter replacement recommended to maintain optimal airflow and system efficiency. All mechanical components, including expansion vessel and control wiring, found to be functioning within normal parameters. System operational and heating properly upon completion of maintenance service.

Completed comprehensive tune-up maintenance on 7-year-old Goodman furnace and tankless water heater, both located in basement. Performed full system diagnostics using digital testing equipment, inspected control board and electrical connections, verified proper operation of all safety controls, and cleaned burner assembly. All components tested within manufacturer specifications and both units operating efficiently with no issues identified.

Conducted comprehensive full system evaluation of existing HVAC equipment in residential basement mechanical room. Assessed current gray metal air handler unit and beige furnace connected via flexible metallic ductwork, including evaluation of humidifier or air filtration component mounted between units. Documented existing equipment configuration, electrical connections, and ductwork layout through detailed photography. Provided customer with professional estimate options for new furnace installation and air conditioning system addition to existing setup. Reviewed mechanical room space constraints and utility connections to determine optimal equipment placement and installation requirements for proposed system upgrades.

Completed HVAC system estimate for replacement of underperforming 10-year-old air conditioning unit and furnace located in basement. Customer reported inadequate cooling performance during humid conditions, with AC providing minimal cool air output. Assessed existing Bryant furnace installation with associated ductwork, refrigerant lines, condensate pump, and exterior condensing unit connections. Provided comprehensive replacement estimate for both heating and cooling equipment to address system inefficiency and performance concerns.

Responded to commercial facility experiencing complete flooding in dock area due to failed sump pump system. Upon arrival, found extensive standing water throughout the loading dock space with significant accumulation and debris. Assessed non-operational sump pump unit and determined pump failure had caused backup, resulting in substantial water damage to concrete block walls, industrial equipment, and floor surfaces. Restored pump functionality and initiated water removal process using industrial extraction equipment. Verified proper pump operation and drainage capability before clearing the service area.

Responded to no-cool complaint on 10-year-old basement AC unit experiencing poor performance during humid conditions. Upon inspection, discovered compromised refrigerant lines with visible wear, deteriorated insulation, and potential leak points on copper piping. Examined compressor electrical connections, noting accumulated dust and aging wire terminals on motor assembly. System showed signs of reduced efficiency consistent with age and lack of maintenance. Documented equipment condition with photos of refrigerant valve assembly and compressor wiring harness for customer review and recommended comprehensive system evaluation to determine whether repair or replacement would be most cost-effective given unit age and current performance issues.

Responded to no-start condition on commercial air conditioning unit. Upon arrival, discovered system was non-operational. Inspected air handling system and found multiple clogged air filters restricting airflow, which likely contributed to system shutdown. Removed and replaced three dirty 16x25x2 pleated air filters from ceiling-mounted filter housing. Verified proper filter orientation with directional arrows for correct airflow. System restored to normal operation following filter replacement. Unit tested and confirmed running properly at completion of service.

Completed full HVAC system installation including 70,000 BTU furnace and 3.5-ton air conditioning unit in basement with outdoor condenser placement in rear yard. Installed new thermostat, humidifier, and reconnected existing ductwork to new equipment. Performed refrigerant charging and system commissioning with digital manifold gauges, verifying proper superheat and subcooling values, temperature differentials, and overall system performance within manufacturer specifications. Requested and coordinated mechanical and electrical permits for installation compliance.

Responded to no-cooling call on 3-year-old attic-mounted slim tech AC unit with history of moisture-related shutdowns and previous motherboard/thermostat replacement. Upon inspection, found extensive water damage to attic floor surrounding air handler, with visible dark staining across multiple OSB panels indicating ongoing condensation issues. Confirmed inadequate or missing insulation on refrigerant lines and condensate management problems causing moisture accumulation on safety sensors, resulting in unit lockout. Documented water damage patterns and uninsulated ductwork contributing to excessive condensation in attic environment. Advised immediate insulation of refrigerant lines, proper condensate drain routing, and evaluation of air handler installation to prevent continued moisture intrusion and potential system failure.

Completed full HVAC system installation including 70,000 BTU furnace with liner and 2.5-ton rear-discharge air conditioning unit. Installed new thermostat, condensate pump, and 4x35 ductwork modifications. Obtained mechanical and electrical permits for furnace and AC installation, reconnected existing electrical service, and registered system with AHRI certificate #215663829 for utility rebate eligibility.

Responded to service call for 32-year-old air conditioning system experiencing loud operational noise during startup and shutdown, along with vibration noise during runtime. Upon arrival, inspected 1994-era condensing unit located in side yard between structures, mounted on concrete pad with lava rock landscaping. Unit was still providing cooling but exhibited signs of significant age-related wear consistent with equipment nearing end of service life. Documented existing installation including electrical service connections, meter configuration, and current equipment positioning. Performed comprehensive evaluation of condensing unit cabinet, fan assembly with protective guard, compressor operation, and mounting stability. Assessed noise sources related to aging mechanical components, worn motor bearings, and potential compressor issues typical of three-decade-old equipment. Photographed current installation showing unit placement, electrical infrastructure, surrounding clearances, and

Completed full HVAC system installation including 70,000 BTU furnace and 2-ton air conditioning unit with outdoor condenser placement in left side yard. Installed new White-Rodgers digital thermostat for system control and reconnected all mechanical and electrical components per code requirements. Obtained necessary mechanical and electrical permits, verified proper blower motor operation, secured all wiring connections, and confirmed system functionality upon startup.

Conducted comprehensive HVAC replacement estimate for residential property where existing 20+ year old air conditioning system experienced catastrophic failure due to fire damage. Assessed outdoor condenser unit positioned on concrete pad in backyard, noting severe damage to electrical components and complete system failure. Evaluated indoor air handler and ductwork infrastructure, including existing Comfortmaker furnace unit and galvanized sheet metal distribution system in mechanical room. Documented current system configuration, refrigerant line routing, electrical connections, and ductwork layout to provide accurate replacement specifications. Recommended complete system replacement due to age of equipment, fire damage to critical components, and safety concerns with continued operation of compromised unit.

Conducted comprehensive assessment of existing HVAC system for medium-sized residential property requiring full system replacement estimate. Evaluated indoor furnace unit with humidifier and air handler located in basement utility room, along with outdoor cylindrical air conditioning unit positioned against exterior brick wall. Documented current equipment configuration including natural gas furnace, ductwork connections, and aging outdoor condenser showing visible weathering and discoloration. Provided complete replacement estimate for heating and cooling system serving approximately 1500-3000 square feet of conditioned space.