Trusted HVAC Services in Sterling Heights, MI

Completed comprehensive Gold-level air conditioning inspection on 6-year-old Daikin residential condenser unit. Performed full system evaluation including filter inspection and removal, photographed equipment condition, and verified proper unit operation and maintenance status per Gold service protocol.

Completed comprehensive NSP AC inspection on 8-year-old residential cooling system with air handler located in basement. Inspected outdoor condenser unit, verified proper operation of fan assembly and motor, removed debris including accumulated leaves from fan guard, and confirmed unit is functioning correctly. All components operating within normal parameters at time of inspection.

Completed Gold AC inspection on a 6-year-old single outdoor condensing unit located at ground level against exterior brick wall. Verified system operational status, inspected condenser coil and fan assembly, checked refrigerant lines and PVC condensate drainage routing to exterior wall, and documented equipment condition with photographic records. All components found functioning properly with homeowner present during inspection.

Completed comprehensive Gold AC inspection on 16-year-old residential HVAC system with equipment located in basement utility area. Performed thorough evaluation of gas furnace unit, ductwork connections, and Bryant Evolution System thermostat to ensure optimal performance and safety compliance. Verified all system components operational, documented equipment condition with photos, and renewed Gold Plan maintenance agreement while on site.

Completed comprehensive AC tune-up on 3-year-old residential system with attic-mounted air handler and ground-level condensing unit. Accessed attic via garage ladder, performed full system inspection including filter check, coil cleaning, refrigerant level verification, electrical connections testing, and thermostat calibration. Outdoor condensing unit inspected and cleaned, all components found operating within normal parameters, system ready for upcoming cooling season.

Completed full HVAC system installation including a 70,000 BTU furnace and 3-ton air conditioning unit positioned on the left side of the property. Installed new programmable thermostat, humidifier, and condensate pump with 600 feet of material run. Reconnected all electrical and gas connections to the new equipment, ran PVC venting from furnace through exterior wall, and integrated ductwork to existing distribution system. Requested mechanical permit prior to installation and ensured all work met code requirements. System tested and verified operational upon completion, with customer qualifying for utility rebate program.

Completed installation of new air conditioning system and evaporator coil in residential basement utility area. System was properly connected to existing furnace, all ductwork secured and sealed, condensate drainage lines installed, and electrical connections completed per manufacturer specifications. Unit tested and verified operational, permit requested for final inspection.

Completed installation of residential tanked water heater in utility room. Connected copper supply lines with brass fittings to unit, installed exhaust venting system with proper pitch and termination, and verified all connections for code compliance. Mounted temperature and pressure relief valve, installed drain pan safety sensor with monitoring device secured to discharge pipe, and set temperature controls to manufacturer specifications. All plumbing connections pressure tested and system commissioned successfully with hot water delivery confirmed throughout residence.

Completed comprehensive Gold-level preventive maintenance inspection on 12-year-old residential HVAC system consisting of one furnace with basement-located air handler and one outdoor condensing unit. Performed multi-point inspection of outdoor AC unit including visual assessment of heat exchanger coils, fan assembly, refrigerant lines, electrical connections, and overall unit condition. Verified system operational status, documented equipment specifications, and confirmed proper installation on concrete pad with adequate clearances for airflow and serviceability.

Completed AC system start-up procedure in basement installation. Verified Honeywell programmable thermostat operation and confirmed proper display functionality showing accurate temperature readings and time settings. System activated successfully with all components operating within normal parameters.

Completed comprehensive Gold AC inspection on 22-year-old residential cooling system with dual outdoor condensing units and laundry room air handler. Performed thorough visual assessment of both exterior condensers positioned on gravel pad, verified proper airflow clearances, inspected fan assemblies and protective grilles, and confirmed operational status of all equipment. System found to be functioning properly with no immediate service concerns identified during inspection.

Completed comprehensive Gold AC inspection on 9-year-old Bryant air conditioning system with air handler located in basement. Performed full system evaluation including visual inspection of outdoor condenser unit, verified proper placement on pad with adequate clearance, inspected electrical disconnect and gas line connections mounted on exterior wall, and assessed refrigerant line routing. Checked condenser coil condition, fan operation, and overall unit integrity. Verified system operating under favorable weather conditions with ambient temperature above 65 degrees as required for accurate performance testing. Removed and disposed of filter packaging per protocol. Advised homeowner to maintain clear area around condenser unit, keeping it free from debris and animal waste to ensure optimal airflow and system efficiency. All system components found to be functioning properly with no immediate service needs identified. Unit exterior and surrounding installation area appear well-maintain

Responded to no heat call on 22-year-old Rheem furnace in basement. Upon inspection, found inducer motor failed with significant deterioration and corrosion of motor housing and components. Blower fan was operational but unit unable to establish proper draft due to failed inducer assembly. Extensive mineral deposits and white residue observed throughout inducer housing, indicating long-term moisture exposure and end-of-service-life failure. Diagnosed complete inducer motor replacement required. Ordered replacement inducer motor from supply house under purchase order for installation.

Completed installation of a 50-gallon short Bradford White tanked water heater in basement utility area. Reconnected all copper supply lines, installed brass shut-off valves with proper venting configuration, and verified system operation with no leaks detected.

Responded to no hot water complaint at 54-year-old residence with 9-year-old water heater in basement. Upon arrival, confirmed water heater was cool to the touch and not producing hot water since previous evening. Performed diagnostic inspection of unit, including examination of gas supply line, pilot light assembly, thermocouple, gas control valve, and venting system. Verified proper gas flow to unit and checked all safety mechanisms and electrical connections. Inspected flue pipe and draft hood for proper ventilation and clearances. Documented current condition of water heater installation with photos showing unit positioning, piping connections, Energy Star rated tank, and overhead gas line configuration with brass fittings. Assessed overall system integrity including copper supply lines, shut-off valves, and temperature-pressure relief valve operation.

Responded to service call for 14-year-old furnace in basement producing clicking noise during operation. Performed diagnostic inspection of air handler unit, ductwork connections, electrical components, and control systems. Upon examination, identified potential issues with blower assembly or gas valve operation causing the audible clicking sound. Inspected electrical transformer box, wiring connections, condensate drainage system, and thermostat control to ensure proper system function and rule out secondary concerns.

Performed cable and camera inspection of underground plumbing lines to assess condition and identify potential blockages or damage. Deployed specialized sewer camera equipment through exterior access point, documenting findings with photographic evidence of line integrity and flow path.

Responded to emergency no-heat call with reported gas odor in basement and complete loss of hot water. Upon arrival, detected natural gas smell near water heater and immediately shut off gas supply at yellow-handled shut-off valve for safety. Inspected gas water heater and associated connections, identifying leak at gas supply line fitting. Ventilated basement area, verified proper ventilation clearances, and confirmed system was safe to repair. Tightened gas line connections, performed leak test with soap solution, and restored gas service after confirming no further leaks present. Relit pilot light, verified proper burner operation, and tested hot water delivery throughout home. System restored to full operational status with no gas odor detected upon completion.

Completed installation of 2.5 ton air conditioning unit with matching evaporator coil in rear discharge configuration. Connected new AC system to existing furnace, verified all refrigerant lines, electrical connections, and condensate drainage were properly installed per manufacturer specifications and local mechanical permit requirements.

Completed comprehensive estimate for replacement of 22-year-old furnace and air conditioning system located in basement. Evaluated existing White-Rodgers programmable thermostat, electrical panel configuration, and circuit breaker capacity to determine compatibility requirements for new HVAC equipment installation.