Expert Heating and Cooling Services in Warren, MI

Responded to service call for leaking shower valve in residential bathroom. Upon arrival, inspected four-handle shower/tub valve assembly mounted on white tiled wall. Accessed plumbing system through wall cavity to diagnose source of leak. Inspection revealed aging valve components and corroded pipe fittings within wall structure. Exposed plumbing infrastructure showed signs of wear consistent with leak symptoms reported by homeowner. Documented existing conditions via photography for service records. Assessed valve assembly and determined repair requirements for proper resolution of leaking condition.

Responded to callback for furnace running but producing no heat in basement location. Performed diagnostic inspection of heating system and heat exchanger assembly, which showed clean condition with no visible damage or obstruction to airflow. Verified thermostat operation showing 72°F set point with heat mode engaged. System requires senior technician follow-up to complete troubleshooting and identify root cause of no-heat condition.

Responded to service call for leaking automatic air vent on residential boiler system approximately 10-15 years old. Upon arrival, inspected boiler and associated components in basement mechanical room. Confirmed active leak at automatic air vent assembly. Assessed condition of existing copper piping, expansion tank, circulator pump, and exhaust venting system. Removed failed automatic air vent from boiler piping. Installed replacement automatic air vent with proper thread sealant and torque specifications. Verified proper operation of new air vent and checked for leaks. Tested boiler system operation and confirmed all components functioning correctly with no active leaks present upon departure.

# HVAC Install - Boiler ## Job Summary Completed residential boiler installation with three-zone heating system configuration, including setup of three thermostats and three zone valves for independent temperature control throughout the home. ## Work Performed Installed new boiler unit in basement mechanical room per manufacturer specifications and local building codes. Configured three-zone hydronic heating system with dedicated zone valves for each heating area, providing individual climate control capabilities. Installed and wired three thermostats to corresponding zones, ensuring proper communication between controls and zone valves. Connected all copper supply and return piping to boiler manifolds with proper isolation valves for future serviceability. Completed all electrical connections including power supply and low-voltage control wiring to thermostats and zone valves. Installed expansion tank and pressure relief valve assembly to protect system from over-pressurization. Tes

# Plumbing Service Report - Water Heater Replacement Responded to service call for leaking water heater in basement. Upon arrival, confirmed active leak originating from tank area. Performed visual inspection of existing unit and surrounding plumbing connections to identify source of failure. Shut off water supply and drained existing water heater to prevent further water damage. Disconnected inlet and outlet copper piping, temperature and pressure relief valve discharge line, and gas supply connection. Removed failed unit from service location. Installed new Rheem Performance tankless water heater as replacement. Positioned unit against concrete block wall in same location as previous heater. Connected cold water inlet and hot water outlet lines using existing copper piping infrastructure. Installed new temperature and pressure relief valve with proper discharge piping. Reconnected gas supply line with appropriate fittings and verified connections for safety. Mounted expansion tan

# Plumbing Install - Tanked Water Heater ## Job Description Completed installation of a Bradford White tanked water heater unit in basement utility area. Installed new water heater with proper venting system, including segmented metallic vent pipe secured with metal clamps and routed at appropriate angle for safe exhaust. Connected copper supply lines to unit with dielectric unions at connection points to prevent galvanic corrosion. Installed shut-off valve with accessible handle for service and emergency shutoff capability. Verified all plumbing connections for proper fit and leak-free operation. System tested and confirmed operational upon completion of installation.

# HVAC Estimate - Boiler Replacement Completed comprehensive assessment of failing residential boiler system located in basement. Primary issue identified was active leak from boiler unit with equipment age exceeding 10 years, warranting full replacement rather than repair. Documented existing hydronic heating system configuration including aged copper distribution piping displaying significant corrosion and oxidation throughout. Multiple supply lines with shut-off valves showed green patina formation and surface degradation consistent with extended service life. Evaluated current piping layout and identified need for hydronic piping relocation under floor as part of replacement scope. Photographed electrical panel configuration and existing plumbing infrastructure to support estimate preparation. Assessed mounting locations, clearances, and utility connections required for new boiler installation. Reviewed basement access, working space availability, and structural considerations f

# Job Description Successfully installed a 40-gallon standard capacity tanked water heater in the mechanical room. The installation included connecting copper supply lines, installing appropriate shut-off valves with identification tags, and routing metallic flexible venting through the existing ceiling structure to ensure proper exhaust ventilation. All plumbing connections were secured and tested, with the unit positioned on the concrete floor and properly integrated into the building's existing utility infrastructure.

# HVAC Estimate - Replacement Summary Completed site assessment for furnace replacement at owner-occupied residence with 32-year-old existing unit located in basement. Documented current system configuration and structural considerations, including attic space utilities routing and exterior access points, to provide comprehensive replacement estimate for new furnace installation.

# HVAC Service - Tune-Up Summary Performed comprehensive furnace tune-up and safety inspection on gas-fired heating unit located in basement. Conducted thorough examination of burner assembly, confirmed proper blue flame combustion pattern indicating correct air-fuel mixture, and inspected all internal components, gas supply lines, and electrical connections. Completed multi-point inspection including thermostat operation, humidifier functionality, and hot water tank assessment as requested for rental property certification requirements. # Detailed Service Report Completed full seasonal maintenance and safety inspection on residential gas furnace system. Upon arrival, accessed unit in basement and performed visual assessment of overall system condition. Unit age was undetermined based on available information. Conducted ignition system inspection and verified proper burner operation. Observed burner assembly during firing cycle, confirming characteristic blue flame pattern across a

Completed comprehensive estimate for furnace replacement on a 6-year-old unit found to be in very poor condition with improper installation, including inadequate mounting without combustible floor protection and incorrectly configured ductwork and flue connections. Provided four estimate options ranging from basic furnace replacement with proper combustible floor kit installation to full HVAC system replacement including air conditioning, with intermediate options for adding cased evaporator coil for future AC compatibility or correcting existing installation deficiencies on current equipment.

# HVAC Service Report - Furnace Repair Responded to service call for furnace failure with no heat condition. Upon arrival, observed pressure switch sensor fault indicated by flashing diagnostic light on control board. Performed system diagnostics and confirmed control board malfunction preventing ignition sequence. Documented existing equipment configuration including water heater and furnace installation in mechanical room with photos of failed control board showing multiple relays and electronic components. Replacement control board was retrieved from shop inventory and installed to restore furnace operation and resolve no-heat condition.

Performed Gold Furnace Inspection on 2006 American Standard furnace located in basement. Inspected blower motor, gas valve, and electrical connections, finding all components in normal working condition with no visible damage, excessive corrosion, or mechanical anomalies. System is operating properly with proper airflow and no immediate service concerns identified.

Conducted inspection of 20-year-old Bryant furnace exhibiting excessive noise and high carbon monoxide levels in exhaust. Documented the existing HVAC system including ductwork configuration and electrical connections. Recommended full replacement due to age of unit and safety concerns identified during assessment.

Responded to a callback for gas odor from a newly installed furnace. Upon inspection, found and corrected improper gas line connection at the shutoff valve. Verified proper operation of the furnace, water heater, and associated venting system. All systems now functioning normally with no gas leaks detected.

Performed diagnostic inspection on noisy furnace for new homeowner. Disassembled and examined blower assembly, finding signs of rust and wear on fan blades. Serviced and reassembled blower unit to reduce operational noise; system now functioning properly with normal sound levels.

Responded to service call for a leaking boiler over 10 years old located in the basement. Upon inspection, identified water staining on the ceiling near the exhaust flue, indicating ongoing leakage from the aging system. Performed diagnostic assessment of the complete heating system including the boiler unit, expansion tank, and associated copper piping network to determine the source of the leak.

Responded to service call for non-functioning White-Rodgers thermostat that failed to maintain settings. Diagnosed issue with 3-year-old unit mounted on wall adjacent to main level utility room furnace. Observed evidence of moisture/mold growth on surrounding wall which may have contributed to operational failure; recommended remediation of wall condition to prevent future thermostat malfunctions.

Completed installation of 70,000 BTU S40 furnace with 500M humidifier and reconnected existing pump. Installed new digital thermostat with proper electrical connections and provided operational documentation to customer. All necessary mechanical and electrical permits were obtained for the installation.

Performed diagnostic testing on 10+ year old furnace in utility room due to improper cycling issues. Utilized True RMS multimeter (UEI DL389B) to test electrical components and verified proper clearances around unit. Identified and corrected cycling problem, restoring normal furnace operation.