Heating and Cooling Grosse Pointe Woods

Completed prepaid maintenance visit on 15-year-old air conditioning system with outdoor condenser unit and basement evaporator coil. Inspected outdoor condenser unit, which showed normal weathering and surface dirt accumulation consistent with age; verified fan operation and checked refrigerant levels. Examined basement mechanical components including motorized damper assembly and associated ductwork connections. System operational at time of service with no immediate repairs required.

Completed annual backflow prevention device certification testing as required by municipal water authority. Performed full inspection and testing of backflow assembly, verified proper operation of check valves and test cocks, and documented all pressure readings to meet city compliance standards. Submitted certification documentation to municipal authorities and provided copy to property owner for their records as requested.

Responded to service call for approximately 30-year-old Janitrol R22 central air conditioning system experiencing loud metal screeching and hub vibration after three minutes of outdoor fan motor operation. Diagnosed failed outdoor fan motor with seized bearings preventing motor shaft separation. Provided replacement estimate for complete system due to age of equipment, R22 refrigerant phase-out, and repair costs approaching replacement value.

Completed full installation of 3-ton Lennox air conditioning system with matching evaporator coil at residential property. Unit positioned on platform on right side of home with proper clearances maintained. Obtained mechanical, electrical, and air conditioning permits prior to installation. Reconnected all electrical and refrigerant lines, performed system startup, and verified proper operation of complete HVAC system.

Completed comprehensive Gold AC inspection on 8-year-old Bryant air conditioning system with air handler located in basement. Unit confirmed operational with outdoor condensing unit properly positioned on rubber pad with adequate gravel drainage bed. Advised customer to maintain clear area around condenser, removing any debris and animal waste to ensure optimal airflow and system performance.

Completed comprehensive Gold AC Inspection on a 10-year-old residential air conditioning system with air handler located in basement and outdoor condenser unit positioned on concrete pad in yard. Performed thorough multi-point inspection including visual examination of condenser fan assembly, protective wire guard, motor housing, and fan blade operation. System found to be in working condition with all components functioning properly at time of inspection.

Completed installation of customer-provided kitchen faucet on double-basin stainless steel sink with chrome single-handle fixture mounted centrally on granite countertop. Inspected under-sink plumbing configuration including PVC P-trap assembly, garbage disposal connections, and flexible supply lines. Addressed customer concern regarding drain line leak connected to washing machine; verified all connections secure and functioning properly upon completion.

Conducted site assessment for estimate to add supply runs to existing Unico system. Inspected Lennox air handler unit located in attic space and evaluated basement mechanical area for potential ductwork routing. Documented current HVAC configuration and spatial constraints to determine feasibility and scope of adding additional supply distribution to improve system coverage.

Responded to no heat/no cool call with thermostat displaying no power after reported fuse failure. Inspected electrical circuit and replaced blown fuse at main panel, restoring 24V power to thermostat in dining room. Verified gas furnace ignition sequence with burners firing properly and outdoor condensing unit operational with fan running. System restored to normal heating and cooling operation with thermostat responding correctly to temperature calls.

Completed comprehensive Gold AC Inspection on 10+ year old residential air conditioning system with outdoor condenser unit and basement-located air handler. Performed multi-point inspection including visual assessment of condenser cabinet, fan assembly with protective guard, refrigerant lines, electrical connections, and overall unit condition. Unit found to be operational with no visible signs of damage, excessive wear, or deterioration, though minor debris accumulation noted around base perimeter requiring standard cleaning maintenance.

Completed Gold AC Inspection on a 7-year-old Bryant air conditioning system. Performed comprehensive evaluation of outdoor condenser unit, which showed normal weathering consistent with age but remained in functional condition. Verified system operation, inspected heat exchanger coils and fins for proper airflow, checked refrigerant lines, and confirmed unit stability on concrete pad. Noted minor debris accumulation on top grille and surrounding area, typical for outdoor equipment. All components operating within normal parameters at time of inspection.

Completed comprehensive Gold AC inspection on outdoor condensing unit located on exterior pad adjacent to residence. Performed multi-point system evaluation including refrigerant pressure readings, electrical connections inspection, condenser coil assessment, and operational testing to verify proper system performance and efficiency.

Completed comprehensive preventive maintenance tune-up on 3-year-old residential air conditioning system. Performed full system inspection including condenser unit evaluation, verified fan motor operation, checked refrigerant levels, cleaned condenser coils, inspected electrical connections, and tested thermostat functionality. All components found operating within normal parameters with no deficiencies noted; system running efficiently and ready for continued service.

Responded to no cooling call on recently installed downstairs air conditioning system that would not turn on. Upon arrival, inspected residential HVAC installation in basement consisting of furnace and air handler with associated ductwork and PVC condensate piping. Investigated electrical panel labeled "Panel B" and reviewed circuit assignments for both upstairs and downstairs AC units. Identified circuit breaker issue affecting downstairs air conditioning unit power supply. Reset tripped breaker on circuit serving downstairs AC system and verified proper electrical connection to equipment. Tested system operation and confirmed downstairs air conditioning unit powered on successfully and began cooling cycle. System returned to normal operation with proper airflow through ductwork and equipment functioning as designed.

Completed plumbing repair in basement utility area addressing water intrusion and drainage issues. Repaired and secured white PVC piping system along concrete block walls, replacing damaged sections and properly fastening with mounting straps. Remediated standing water on concrete floor, identified source of leak at wall penetration point, and sealed damaged wall opening where pipe enters structure to prevent future water accumulation.

Completed comprehensive Gold Plan preventive maintenance inspection on 9-year-old outdoor AC condenser unit. Performed full system evaluation including refrigerant level check, electrical component testing, condenser coil cleaning, fan motor operation verification, and overall performance assessment. Unit found to be operating within normal parameters with all components functioning properly; no repairs required at this time.

Completed comprehensive tune-up and city certification inspection on 13-year-old Carrier furnace system located in basement. Performed full system diagnostics, inspected evaporator coil assembly showing signs of dust accumulation, verified proper operation of Carrier humidifier unit and all refrigerant lines, confirmed all safety controls and electrical connections were secure, and validated system met municipal code requirements for certification.

Completed annual backflow prevention device testing on exterior gas valve assembly mounted on brick wall per homeowner request. All components inspected, test valves operated properly, and system verified to be functioning within acceptable parameters to prevent reverse flow contamination.

Responded to a plumbing service call at a 76-year-old residential property requiring water pipe capping in the basement. Upon arrival, inspected the basement utility area containing a sump pump pit system with multiple exposed PVC and metal pipes that had been left uncapped for an extended period. The work area included white PVC drainage lines, rusted metal piping, and various plumbing connections around the sump pit with visible water damage and moisture staining on surrounding surfaces. Successfully capped all exposed water pipes in the basement to prevent water flow and potential flooding. Work focused on securing open pipe ends with appropriate caps and fittings to ensure proper water shutoff. The installation addressed immediate concerns related to the uncapped pipes that posed risks of water damage and system inefficiency. All capping work was completed using industry-standard materials compatible with the existing PVC and metal pipe infrastructure present in the 1950s-era home

Completed full HVAC system installation including 90,000 BTU high-efficiency furnace, 2.5-ton air conditioning unit, programmable thermostat, and humidifier in unfinished basement location. Installed new metallic ductwork with insulation wrapping, connected copper refrigerant lines, and ran PVC venting for condensate drainage. Mounted furnace on concrete floor against block wall foundation with proper clearances. Ran black electrical conduit and wiring for power connections. Installed supply and return air plenums with pink foam insulation board. Connected all ductwork to existing trunk lines with 600 CFM airflow capacity. Installed condensate pump for drainage management and performed system flush. Reconnected existing electrical circuits as required. Verified proper refrigerant charge and system pressures. Tested all safety controls, ignition sequence, and airflow distribution. System startup completed with all equipment operating within manufacturer specifications. Mechanical and el