Heating and Cooling Grosse Pointe Woods

# Plumbing Service - Clogged Drain/Sink Responded to a main drain backup issue affecting the kitchen drainage system. Upon arrival, found the main drain line was experiencing blockage causing water to back up when kitchen fixtures were in use, while bathroom drains remained functional. Inspection revealed significant water damage on the basement floor with standing water and staining patterns indicating recent overflow events. Located the main drain cleanout access point in the basement utility area near the plumbing assembly. Assessed the drainage system configuration including vertical stack pipes and horizontal drain lines. Utilized drain cleaning equipment to clear the obstruction in the main line. Successfully restored proper drainage flow to the kitchen plumbing system. Verified clearance by running water through kitchen fixtures and confirming no backup occurred. Advised on the existing water damage conditions observed in the basement and recommended monitoring for future drai

Responded to emergency water pump failure in 1947 residential property affecting hydronic heating system. Upon arrival, assessed damaged circulator pump that had overheated, causing smoke and thermal damage to adjacent water heater components. Replaced failed circulator pump with new unit, installed on plywood mounting panel alongside existing pump in dual-zone configuration. Reconfigured copper and brass piping network to accommodate new pump installation, including integration with existing PEX tubing distribution lines. Installed new shut-off valves with red wheel handles at strategic control points throughout the system for proper isolation capability. Verified all brass fittings and couplings were properly secured and leak-free. Tested both circulation pumps for proper operation and flow direction. Confirmed electrical connections were secure and properly grounded. System pressurized and tested for leaks at all connection points. Verified proper operation of all zone valves and sh

Completed comprehensive spring maintenance on 10-year-old air conditioning system located on west side of property. Performed full AC tune-up including inspection of outdoor condensing unit electrical components, capacitor testing, contactor examination, and control board verification. Inspected indoor air handler unit, confirmed 20x25x4 filter specifications for Mitsubishi system, checked electrical connections and wiring integrity throughout system, and utilized diagnostic meters to verify proper amperage draws and system performance. All components found operational and system ready for cooling season.

Responded to no heat call for furnace located in upstairs bedroom closet. Upon inspection, found unit powering on but failing to produce adequate heat. Accessed blower assembly and discovered significant dust accumulation on centrifugal fan blades and housing components affecting airflow efficiency. Inspected electrical connections and wiring harness, confirming all wire terminals and connectors were secure with no visible damage. Examined inducer motor assembly and verified proper operation. Cleaned blower wheel and housing to restore optimal air circulation. Checked all safety controls and limit switches for proper function. System tested and confirmed return to normal heating operation with proper temperature rise across heat exchanger.

Responded to no-heat call where thermostat displayed error code on 14-year-old furnace located in basement. Diagnosed failed heat exchanger requiring full unit replacement. Provided comprehensive replacement estimate and documented exterior conditions including chimney requiring possible new liner and existing PVC vent termination through brick wall.

Responded to no-heat call on 14-year-old furnace displaying thermostat error code. Performed diagnostic inspection using borescope camera to examine heat exchanger and internal components for cracks, corrosion, and blockages. Inspected blower wheel assembly and found moderate dust accumulation on blades affecting airflow efficiency. Cleaned blower wheel, verified proper operation of all mechanical and electrical components, cleared error code, and restored heating system to normal operation.

Responded to a plumbing service call for bathroom sink maintenance. Upon inspection, serviced a traditional two-handle chrome faucet and white porcelain sink assembly. Verified proper operation of the drain stopper mechanism and inspected the P-trap assembly beneath the sink, confirming all PVC drain connections and chrome tailpiece were secure and leak-free. Checked both hot and cold water supply lines with mounting brackets for proper connection to the faucet assembly. All plumbing components were found to be in standard working condition with no visible leaks or damage detected.

Responded to no cooling complaint on six-year-old Trane commercial rooftop unit. Upon inspection, diagnosed failed control board causing system malfunction. Replaced defective control board with OEM replacement part under existing purchase order, verified all electrical connections, and tested system operation. Unit restored to full cooling capacity with proper airflow and temperature differential confirmed.

Conducted comprehensive site assessment for complete HVAC system replacement at residential property. Evaluated existing outdoor condensing units showing significant age-related deterioration, dirt accumulation, and weathering on exterior panels. Documented current dual-unit configuration positioned on concrete pads in side yard location. Inspected interior ductwork system and plenum, noting recent electrical line installation along main trunk line. Photographed existing equipment conditions and infrastructure to support full system replacement proposal. Provided detailed quote for new HVAC system installation including equipment specifications and labor requirements.

Completed comprehensive Gold Furnace Inspection as part of complimentary spring tune-up service for 12-year-old heating system located in basement. Performed full system evaluation including visual inspection of furnace components, heat exchanger examination, burner assembly assessment, and verification of all safety controls and limit switches. Cleaned and inspected blower assembly, checked belt tension and condition, and lubricated motor bearings as needed. Tested ignition system operation, verified proper flame characteristics, and measured temperature rise across heat exchanger to ensure efficient operation. Inspected venting system for proper draft and secure connections, checked condensate drain for blockages, and verified all electrical connections were tight and secure. Replaced air filter and cleaned flame sensor to optimize performance. Tested thermostat operation and calibration, confirmed proper system cycling, and documented all operational parameters within manufacturer s

Completed furnace replacement estimate for basement installation with equipment age exceeding 10 years. Assessed existing gray metal cabinet furnace unit with horizontal ductwork and galvanized metal plenum connections. Documented current system configuration including ductwork transitions, utility room layout, and equipment accessibility for replacement planning. Photographed installation area showing concrete block walls, concrete flooring, and proximity to water heater to determine clearance requirements and proper equipment sizing for future replacement.

Completed comprehensive Gold-level furnace inspection on a 2-year-old forced air heating system located in the basement. Performed thorough visual examination of all accessible components including heat exchanger, burner assembly, blower motor, and electrical connections. Inspected condensate pump and drainage system, verified proper operation of all safety controls, and examined ductwork connections. Documented equipment condition through photographic records showing internal components and overall system installation. All components found operating within normal parameters with no immediate service needs identified.

Completed full HVAC system installation including a 110,000 BTU gas furnace with right-side configuration and 4-ton air conditioning unit in residential mechanical room. Installed Aprilaire humidifier mounted on furnace, new thermostat, and 20x25x1 filter base with 600 CFM airflow capacity. Ran new PVC venting and drainage lines, connected copper refrigerant lines, and installed metallic ductwork with proper segmented joints. Mounted exterior electrical disconnect and established utility meter connections on exterior brick wall. Reconnected all necessary gas, electrical, and plumbing connections. Obtained mechanical and electrical permits and remeasured return air for proper system sizing. System qualified for utility rebate program and passed all code inspections.

Completed comprehensive Gold Furnace Inspection on a 13-year-old Bryant forced air heating system located in the basement. Performed full system evaluation including visual inspection of furnace cabinet, ductwork, and humidifier control components. All equipment found to be in operational condition with humidifier control panel functioning properly and ductwork showing no signs of deterioration or damage. Documentation photos captured for service records.

Completed comprehensive tune-up on 4-year-old furnace located in basement. Performed full system inspection including blower motor assembly, electrical connections, and all internal components. Per customer request, inspected and evaluated pump system; verified proper operation and found all equipment functioning within normal parameters with no issues identified.

Completed comprehensive tune-up and safety inspection on furnace over 10 years old located in basement for city inspection compliance. Verified proper ignition sequence and burner flame characteristics, confirmed all gas connections secure with no leaks detected, and inspected heat exchanger for integrity. Tested all safety controls including limit switches and flame sensor, cleaned burner assembly, checked and adjusted gas pressure, and verified proper venting and combustion air supply. System operating safely and efficiently within manufacturer specifications; all components functioning properly with no immediate concerns noted.

Completed comprehensive tune-up and city inspection preparation on 8-10 year old gas furnace located in basement. Performed full system evaluation including burner assembly operation verification, heat exchanger inspection, blower motor assessment, electrical connection testing, and ductwork examination. All components found operating within normal parameters with burner flames showing proper blue combustion pattern and system controls functioning correctly.

Responded to service call regarding recently installed electrical outlet for stove connection. Inspected existing outlet mounted on concrete block wall and discussed rotating receptacle 90 degrees to accommodate appliance cord orientation. Documented current installation with photographs showing outlet box properly secured to wall with cord connected and verified electrical functionality prior to any modifications.

Completed installation and startup of Lennox model ML13KC1-030-230A04 air conditioning system with R-454B refrigerant. Unit was properly mounted on a black pad with gravel base, with all refrigerant lines and electrical connections secured according to manufacturer specifications. System was successfully tested and is operating within normal parameters.

Performed comprehensive inspection of residential property to assess GFI outlet requirements. Utilized Klein voltage tester to evaluate multiple outlets throughout the home, identifying areas requiring code-compliant GFI protection. Provided homeowner with recommendations for necessary electrical safety upgrades to ensure compliance with current electrical codes.