Heating and Cooling Bloomfield Hills

Completed annual cooling maintenance inspection on Bryant air conditioning system under prepaid gold plan agreement. Performed comprehensive AC tune-up including visual inspection of outdoor condenser unit, verified proper operation of fan motor and compressor, checked refrigerant levels, cleaned condenser coils, and inspected electrical connections and controls. System operating properly with no deficiencies noted; unit in good working condition and ready for continued service through 2026 maintenance cycle.

Responded to no-heat complaint on Daikin mini-split heat pump system serving sunroom, installed December 2020. Performed diagnostic testing using digital manifold gauges to assess refrigerant pressures and system operation at outdoor condenser unit. Identified failed service valves requiring replacement and contacted technical support for troubleshooting assistance. Service valves ordered from factory under PO 1305460-001 for delivery to Williams Southfield branch. Follow-up visit required to complete valve replacement and verify proper heat pump operation once parts arrive.

Responded to service call for air conditioning unit not cooling effectively. Upon arrival, performed visual inspection of outdoor condensing unit and associated components. Examined electrical disconnect box, refrigerant line sets with black foam insulation, and service valve connections at brick wall mounting point. Inspected unit for proper installation, secure line set connections, and signs of refrigerant leakage or moisture issues. Verified electrical connections at disconnect panel and assessed overall system condition. Documented equipment setup including gray metal condensing unit positioned on concrete pad, refrigerant lines properly secured with white plastic clips, and service valves accessible for maintenance. Completed diagnostic assessment of outdoor unit installation and cooling system performance.

Completed comprehensive Gold AC Inspection and seasonal maintenance on two residential air conditioning systems (4-year-old and 6-year-old units) located at exterior and basement positions. Performed full system diagnostics including refrigerant level verification, electrical component testing, condenser coil cleaning, air filter inspection and replacement, thermostat calibration, and condensate drain line clearing. Inspected outdoor condenser unit with top-mounted fan assembly, verified proper operation of fan motor and protective wire guard, examined housing integrity and coil fins for damage or debris accumulation, and confirmed adequate airflow through perforated side grilles. Tested compressor amperage draw and capacitor performance to ensure optimal efficiency. Evaluated both systems for pre-summer readiness, finding units operating within manufacturer specifications with no immediate repairs required. Documented equipment condition through photographic records showing clean exte

Completed comprehensive Gold AC Inspection on dual-zone residential cooling system including newer attic-mounted upstairs unit (2 years old) and older outdoor downstairs condenser unit. Performed full system diagnostics, refrigerant level verification, electrical component testing, and airflow measurements on both units. Outdoor condenser exhibited significant biological growth with moss and algae accumulation on fan cover, housing louvers, and upper surfaces due to extended exposure and deferred maintenance. Cleaned condenser coils, removed organic debris, treated biological growth, and restored proper airflow capacity. Inspected and cleaned condensate drain lines, verified thermostat calibration, tested capacitors and contactors, measured amp draw on compressor and fan motors, and confirmed proper cycling on both systems. All components operating within manufacturer specifications following maintenance procedures. Recommended ongoing seasonal maintenance to prevent future biological

Completed comprehensive Gold AC preventive maintenance inspection on two residential HVAC systems, approximately 7 years old, with air handler located in basement. Performed multi-point inspection of both outdoor condenser units, including examination of Evolution series equipment, protective grilles, refrigerant line connections, and overall system components. Documented equipment condition through photographic records, noting weathering and dirt accumulation on condenser housings and grilles consistent with normal outdoor exposure for equipment of this age.

Completed comprehensive Gold Furnace Inspection on a single basement-located heating unit over 10 years of age. Performed thorough examination of all furnace components including burner assembly, ignition system, blower motor, control board, and electrical connections. Verified proper operation of the REME-HALO air purification system mounted on the ductwork, confirming secure installation and UV light functionality. Inspected flame sensors, heat exchanger, and gas valve operation. All safety controls, including high-limit switches and rollout protection, tested and verified operational. Blower motor and capacitor inspected for proper function. System cycling confirmed normal with proper ignition sequence and blue flame pattern observed. Unit operating within manufacturer specifications with no immediate service needs identified.

Responded to no cooling complaint on residential property with multiple HVAC systems. Upon arrival, located and inspected three outdoor condenser units positioned on gravel pad with adequate clearance. Units showed signs of normal wear with debris accumulation on top surfaces including leaves and dirt. Verified all condensers were beige-colored cabinet style units with wire fan guards and louvered side panels for proper ventilation. Noted condensate drainage lines present and vegetation growth in close proximity to equipment. Documented equipment condition through photography showing manufacturer labels and warning stickers visible on unit panels. All units appeared to be standard residential split-system configurations with top-discharge fan assemblies mounted on concrete pads with gravel surround for drainage.

Responded to no-cooling call on 10+ year old air conditioning system. Upon arrival, performed electrical diagnostics using digital multimeter and clamp meter to test voltage and amperage at outdoor condensing unit. Inspected indoor evaporator coil in basement and verified electrical connections, control wiring, and refrigerant lines. Measured system voltages and current draw to identify cause of unit failure to start.

Installed a 50-gallon standard tanked water heater in residential utility room with complete plumbing reconnection. Connected hot and cold water supply lines using copper piping, installed circulation pump assembly with electrical wiring, and secured all connections with appropriate shutoff valves. All plumbing connections were properly fitted with Charlotte Pipe PVC components where applicable, system was tested for proper operation, and installation meets mechanical code requirements.

Completed comprehensive Gold AC inspection on 2018 residential air conditioning system with air handler located in basement and outdoor condenser unit positioned on concrete pad. Performed thorough evaluation of system components, verified operational status of condenser unit with top-mounted fan assembly and wire guard protection, and inspected airflow through metal mesh grilles on unit cabinet. Noted minor debris accumulation of leaves around condenser base and recommended routine clearance maintenance to ensure optimal airflow and system efficiency.

Completed Gold AC Inspection and tune-up as part of plan membership. Performed comprehensive system evaluation including inspection of electrical components, capacitor, contactors, and control wiring. All components found operating within normal parameters, documentation photos captured of electrical panel showing ARD capacitor and associated control circuits in proper working condition.

Responded to service call for heating issue affecting only half of the residence after homeowner self-installed a new Nest thermostat in hallway location. Performed diagnostic evaluation of the newly installed thermostat system, which displayed heating mode active at 70°F setpoint with indoor temperature reading 66°F. Verified proper thermostat mounting, wiring connections, and system communication to identify cause of partial heating distribution issue and restored full system functionality.

Installed Lennox 110,000 BTU furnace in basement utility area with complete electrical reconnection and ductwork integration. Submitted permit requests for mechanical, electrical, and furnace work, and processed utility rebate application. All systems tested and operational upon completion.

Responded to service call for 10-year-old Payne furnace system with half of residence receiving cold air while other zones functioned properly. Accessed unit in utility room, removed cabinet panel, and performed diagnostic inspection of control board, blower assembly, and zone damper system. Identified control board malfunction affecting zone valve operation, inspected all electrical connections and wiring harnesses, and verified proper LED indicator status on circuit board to isolate the issue causing uneven heating distribution throughout the home.

Completed AC system start-up for basement coil installation. Performed operational testing of Lennox outdoor condensing unit, verified proper refrigerant charge, confirmed electrical connections, and ensured system is functioning within manufacturer specifications.

Replaced inducer motor on gas heating system. Verified proper burner operation with visible blue flame pattern across burner assembly. Performed combustion analysis using digital analyzer, confirming oxygen levels at 8.4%, carbon monoxide at 28 PPM, and stack temperature at 37.9°F. All system components tested and operating within manufacturer specifications.

Responded to service call for leaking dehumidifier located in basement. Upon inspection, found evaporator coil heavily contaminated with dust and debris accumulation throughout the honeycomb mesh structure, causing restricted airflow and improper condensate drainage. Performed thorough cleaning of evaporator coil, removed debris buildup from mesh pattern, cleared condensate drain line, and tested unit operation to confirm proper function and elimination of water leak.

# Water Heater Service Call Responded to no hot water complaint on six-year-old residential gas water heater in basement storage room. Upon arrival, performed diagnostic inspection of unit originally installed by Flame. Examined water heater tank, gas valve control assembly, supply and discharge piping, and pressure relief valve. Checked digital temperature controller display for proper operation and settings. Inspected all plumbing connections at top of tank including hot and cold water lines. Evaluated gas line connections and control valve functionality. Assessed overall unit condition and verified all safety labels and manufacturer specifications were intact. Documented equipment status with photographic evidence showing complete installation setup and control panel readings. Unit evaluated for potential repair versus replacement options based on age and service history.

Responded to service call for toilet producing loud noise during flush cycle. Upon inspection, removed tank lid and identified discolored water with significant mineral deposits and corrosion throughout tank components. Diagnosed noisy flush as likely caused by deteriorated fill valve assembly and sediment buildup affecting flush valve mechanism, as evidenced by rusty brown water discoloration and visible mineral accumulation on internal plumbing components.