Heating and Cooling Bloomfield Hills

Completed Gold Boiler Inspection on multi-unit property with hot water boiler, furnace, and two air conditioning systems (equipment dated 2022-2024) located in basement and attic areas. Performed comprehensive combustion analysis using digital meter, recording oxygen levels at 9.6%, temperature reading of 149.4°F, and verified proper fuel-to-air ratios with all measurements within acceptable parameters. Inspected all equipment components, verified operational status of all four units, and documented system conditions with no deficiencies noted.

Rebuilt Delta widespread lavatory faucet by installing new cartridges, seats, and springs, and straightened both handles to restore proper operation. Replaced the existing shut-off stops and swapped out the chrome P-trap with a new bag trap. Additionally, installed a round toilet seat on the basement toilet and addressed the toilet plunger issue in the main bathroom.

Completed Gold preventative maintenance inspection on 13-year-old hot water boiler located in garage. Performed comprehensive system evaluation including visual inspection of internal components, control panel functionality verification, wiring harness examination, and safety control testing. Unit found operating properly with normal wear consistent with age; all low voltage controls, limit switches, and power indicators functioning as designed.

Completed comprehensive Gold Furnace Inspection on two forced-air heating units located in basement, including a 2025 model and a 2009 Goodman unit (model AMH950904CXAF). Performed combustion analysis using Testo 310 analyzer, which measured carbon monoxide levels at 499 ppm and temperature at 82°F. Conducted full safety inspection, verified proper operation of both systems, documented equipment conditions with photographs, and confirmed all components functioning within normal parameters.

Completed annual Gold Plan furnace inspection on one-year-old unit. Performed comprehensive system evaluation including visual inspection of all internal components, gas valve assembly, electrical connections, and blower motor. Conducted combustion analysis testing using Testo 310 analyzer to verify proper efficiency and safe operation. Verified humidistat control settings and ductwork connections. All components operating within manufacturer specifications with no deficiencies noted. System found in excellent condition with no repairs required.

Completed comprehensive Gold Furnace Inspection on basement-located forced air heating system. Performed full combustion analysis using diagnostic meter, confirming CO readings at 16 PPM, CO2 at 8.2%, and combustion efficiency at 89.2% with 45.5% excess air. Inspected all internal components including blower motor assembly, burner ports, heat exchanger, electrical connections, and gas valve operation. All systems operating within manufacturer specifications with no safety concerns identified.

Completed comprehensive Gold Furnace Inspection on 10+ year old forced air system located in basement. Performed thorough visual examination of furnace components, utilized digital borescope to inspect interior ductwork and heat exchanger for cracks or deterioration. Verified all electrical connections, examined wiring integrity, and assessed overall system operation. Unit confirmed to be in working condition at time of inspection. Also observed water heater with American Water Heater Company Proline Flame Guard branding showing significant copper pipe corrosion and oxidation on supply lines, noted blue-handled shut-off valve and exhaust flue connections. Documented all findings with photographic evidence for maintenance records.

Conducted on-site evaluation for complete HVAC system replacement at residential property with 20-year-old equipment operating at minimal capacity. Assessed existing outdoor condensing unit positioned on concrete pad against brick exterior wall with dual electrical disconnect boxes, along with natural gas furnace located in basement. Documented current system configuration, electrical connections, and installation conditions to provide comprehensive replacement estimate for new air conditioning and heating equipment.

Completed full installation of 2.5-ton counterflow air conditioning system with matching evaporator coil at rear location. Installed new Ecobee 3 Lite thermostat and condensate pump, performed all electrical and mechanical connections per code requirements. System charged with R454B refrigerant, verified proper pressures and temperatures using manifold gauges, and confirmed all components operational within manufacturer specifications.

Returned to property to complete plumbing installation by installing new trap assembly and discharge line using white PVC piping with proper fittings and connections. Work was performed in basement utility area, connecting to existing vertical drain stack with appropriate coupling, ensuring proper drainage flow and code-compliant trap configuration.

Completed installation of 24kW Generac standby generator system with automatic transfer switch mounted on exterior brick wall. Installed RXSW150A3 Generac Transfer System with proper electrical connections including heavy-gauge supply and load conductors, grounding system, and control module wiring with AC circuit monitoring capabilities. All electrical, mechanical, gas piping, and generator permits were obtained and installation was performed to code requirements with transfer switch properly configured for automatic operation during utility power loss.

Responded to no heat call on 4-year-old furnace located in basement. Upon arrival, confirmed unit was not operating. Performed diagnostic testing and determined blower motor had failed. Removed defective blower motor assembly using reciprocating saw to access mounting hardware. Ordered replacement blower motor from Dakota Supply Sterling Heights under PO 1368325-001 for installation upon arrival. Unit equipped with Carrier humidifier system, which was unaffected by the motor failure. Verified all ductwork connections and seals remained intact during disassembly process.

Responded to service call for non-operational garbage disposal unit installed in main kitchen sink. Upon arrival, conducted diagnostic assessment of the disposal system, including electrical connections, reset button, and internal components. Determined root cause of malfunction, performed necessary repairs or replacement, and restored unit to full working condition. Tested disposal operation under running water to verify proper functionality and confirmed no leaks or abnormal sounds during operation cycle.

Completed annual Gold furnace inspection on 7-year-old unit located in basement. Performed comprehensive tune-up including visual inspection of all internal components, electrical connections, and control systems. All wiring, transformer, and safety controls found to be in proper working condition with no issues identified.

Completed comprehensive Gold furnace inspection and fall maintenance tune-up on basement-located unit with no reported issues or symptoms. Performed full system evaluation including inspection of gas valve assembly, electrical connections, wiring harnesses, pressure switches, and all mechanical components. Documented equipment condition with interior compartment photos showing proper component configuration and connections.

Assessed non-operational 14-year-old generator unit located outdoors for replacement estimate. Documented existing equipment condition and surrounding mechanical systems including HVAC components and water heater in basement utility area to determine installation requirements and specifications for new generator system.

Completed full installation of 3.5-ton A/C system with evaporator coil and 2000 media cabinet in interior utility closet. Air handler unit positioned and secured on concrete floor with electrical conduit run and connected, condensate drain line installed, and all manufacturer specifications verified. System wired per code requirements with mechanical and electrical permits requested, unit tested for proper operation, and rear discharge configuration confirmed with all connections remeasured for accuracy.

Removed shark bite 90-degree fitting from upstairs heating register and installed permanent sweat or press connection to allow proper flush mounting of register cover. Installed one register coupling on downstairs heating unit. Coordinated with boiler technician for follow-up service after plumbing repairs were completed.

Conducted site assessment for new whole home generator installation at manufactured home residence. Evaluated existing electrical panel capacity and basement infrastructure to determine optimal generator placement and connection requirements. Additionally assessed HVAC system for humidifier installation quote, documenting current ductwork configuration and electrical routing through basement joists.

Completed outdoor spigot replacement for homeowner. Removed and replaced corroded exterior hose bib due to extensive rust and deterioration of existing fixture. New spigot installed with proper connections to existing plumbing system, ensuring secure mounting and leak-free operation.