Heating and Cooling Bloomfield Hills

Completed comprehensive Gold AC inspection on single 2017 residential cooling system with air handler located in basement and outdoor condenser unit positioned on grade next to building exterior. Performed full system evaluation including visual inspection of condenser cabinet, fan assembly, and protective grille, verified unit operational status, and documented equipment condition through photographic records. Confirmed surrounding area clear of debris and system functioning properly with homeowner present at time of inspection.

Completed estimate for replacement of two residential air conditioning units, both approximately 20 years old, located in basement. Units were evaluated following discovery of blown fuse during scheduled maintenance visit. Due to age of equipment and homeowner's preference to avoid further repair investments, full system replacement was recommended for both AC units. Assessment included inspection of existing ductwork, condensate drainage systems, and electrical connections visible in basement utility area.

Responded to complaint of sulfur odor emanating from two tanked water heaters in residential property. Inspected both units and confirmed hydrogen sulfide smell commonly associated with bacterial reaction with magnesium or aluminum anode rods. Observed evidence of water leakage and moisture damage on basement concrete floor near equipment area. Documented existing conditions including water staining and HVAC equipment proximity. Recommended anode rod replacement with powered anode or zinc-aluminum alloy rods to eliminate sulfur bacteria growth and odor issue in both water heating systems.

Completed comprehensive Gold AC inspection on a 2017 residential cooling system with outdoor condenser unit and basement-located air handler. Performed multi-point system evaluation including visual inspection of condenser coils, fan operation, electrical connections, refrigerant lines, and overall equipment condition. Unit found operating properly with minor debris accumulation on top surface noted; all components functioning within normal parameters.

Replaced existing 50-gallon residential water heater that was failing to maintain proper water temperature. Installed new tanked water heater unit with copper supply line connections, pressure relief valve, and proper venting. Reconnected all plumbing fixtures, tested system operation to verify adequate hot water production and temperature output, and ensured all connections were secure and leak-free upon completion.

Performed seasonal air conditioning system start-up on outdoor condenser unit. Completed visual inspection of equipment, verified proper operation of compressor and condenser fan motor, and confirmed system achieved appropriate cooling cycle. Removed debris and leaves from unit exterior and surrounding area to ensure adequate airflow through condenser coils.

Completed Gold AC Inspection on 9-year-old residential air conditioning system. Unit operational at time of service with outdoor condenser showing normal weathering for age; visual inspection performed and system parameters verified within acceptable ranges. Basement evaporator coil noted for future reference.

Performed system start-up on newly installed basement air conditioning coil. Verified electrical disconnect operation, confirmed proper equipment installation, and inspected air filtration system. Unit tested and operational with all components functioning within manufacturer specifications.

Responded to service call for air conditioning system not operating due to blown fuse. Upon arrival, performed diagnostic inspection of 10+ year old AC unit located in basement. Confirmed blown fuse in disconnect box and inspected system for underlying electrical issues or short circuits that may have caused fuse failure. Examined condensing unit, evaporator coil assembly, and associated ductwork in attic space for any signs of electrical fault, refrigerant leaks, or mechanical failure. Replaced blown fuse with proper amperage rating and verified all electrical connections were secure and within manufacturer specifications. Cycled system through complete startup sequence to ensure proper operation of compressor, condenser fan motor, and blower assembly. Monitored amp draw on all components to confirm normal operating parameters. System restored to full operational status with no additional faults detected.

Completed comprehensive Gold AC Inspection on 3-year-old Trane cooling system with air handler located in basement. Performed full system evaluation including condenser unit examination, refrigerant line inspection, electrical connections check, and airflow assessment. Unit operating properly with no deficiencies noted at time of inspection.

Responded to intermittent leak from rarely used shower head in master bathroom of 1968-built home. Upon inspection, identified malfunctioning tub spout diverter causing water to flow simultaneously from both shower head and tub spout during shower operation. Accessed plumbing infrastructure through existing wall panel to inspect valve assembly and supply lines for potential water intrusion. Replaced defective diverter mechanism and tested system under full water pressure to confirm proper operation and complete water diversion to shower head. Verified no moisture present in wall cavity and confirmed all connections sealed properly with no active leaks detected.

Completed comprehensive Gold AC inspection on basement-located HVAC system with Bryant equipment. Performed full system evaluation including thermostat operation verification at Emerson digital control set to 71 degrees, visual inspection of furnace unit and air handler components, assessment of ductwork connections, and examination of electrical connections at junction box. All components photographed and documented, system found operational with no immediate service requirements identified during inspection.

Completed scheduled maintenance plan on a 13KW Briggs & Stratton standby generator. Performed standard preventive maintenance procedures including battery inspection and service, verified proper terminal connections, and ensured unit operational readiness. Generator confirmed in working condition upon arrival and completion of service.

Completed comprehensive Gold AC inspection on a 6-year-old residential air conditioning system with air handler located in basement. Performed thorough evaluation of outdoor condenser unit, which showed normal weathering consistent with age, and verified all system components were operational at time of inspection. Confirmed adequate clearance around condenser unit, inspected fan assembly and protective guard for proper operation, and documented equipment condition through photographic records.

Completed gas line installation in residential property, running black iron pipe vertically along interior corner wall with proper securing brackets at code-compliant intervals. Installation includes multiple fittings and elbows to ensure proper routing and connection. Work performed in utility/laundry area and garage space, with all pipe securely fastened to wall structure using metal straps per industry standards.

Completed installation of new air conditioning system and evaporator coil in residential basement location. Established all electrical connections at terminal block, routed refrigerant lines with proper insulation, and installed condensate drain lines using PVC piping. System was fully wired, tested for proper operation, and permit was requested for the installation per local code requirements.

Conducted comprehensive estimate for complete HVAC system replacement in attic location. Evaluated 30-year-old Unico system utilizing R22 refrigerant with failed compressor exhibiting excessive amperage draw. Identified critical safety hazard with compressor wiring showing thermal damage, burning, and insulation bubbling. System was immediately shut down to prevent fire risk and further equipment damage. Documented existing flexible ductwork installation, including 18-inch diameter ducts with age-related deterioration, and assessed attic-mounted air handler/coil configuration. Performed gold-level AC inspection protocol for attic-installed equipment. Photographed existing ductwork conditions, insulation coverage, and HVAC infrastructure to support replacement specifications and scope of work.

# HVAC Maintenance - Gold AC Inspection Completed comprehensive Gold AC inspection on 25-year-old residential air conditioning system with air handler/coil located in attic. Performed thorough visual assessment of both indoor and outdoor components per maintenance protocol. ## Outdoor Unit Assessment Inspected condenser unit and documented significant deterioration of electrical components. Found severe corrosion and oxidation on terminal block connections, with heavy rust accumulation obscuring metal surfaces. Multiple wire connections showing signs of environmental exposure and aging, though conductors remain structurally intact. Capacitor and associated wiring connections examined. Noted accumulated dirt, debris, and cobwebs throughout electrical assembly. All colored conductors traced and connection integrity verified despite visible surface corrosion on terminals. ## Indoor Unit Assessment Accessed attic-mounted air handler and inspected electrical panel and junction box. Fou

Completed annual Gold AC Tune-Up on 1-year-old Lennox air conditioning system. Performed comprehensive cooling maintenance inspection including condenser unit evaluation, refrigerant line assessment, and operational testing. System confirmed operating properly with all components functioning within normal parameters. Unit shows typical outdoor weathering with dirt accumulation on exterior panels and coil fins, but all mechanical and electrical components maintain structural integrity. Documented equipment condition with photos for service records.

Completed comprehensive Gold AC inspection on multi-unit residential system with air handler located in basement. Performed full system evaluation including condenser unit inspection, verified operational status of all components, checked electrical connections and wiring integrity, examined refrigerant lines and fittings, and assessed overall equipment condition. Unit found to be operational at time of inspection with all major components functioning as designed.