HVAC, Plumbing and Electrical in Detroit

Replaced severely corroded steam line segments in basement utility area, focusing on sections with extensive rust damage and failing joints. Installed new pipe fittings with proper thread sealant at connection points and tested system to ensure proper steam distribution without leakage.

Performed main drain cleanout service in mechanical room, addressing insulated pipe system with visible black insulated piping and silver flexible ducting. Inspected and secured metal clamp/hanger assembly on wall-mounted components to ensure proper drainage function.

Performed routine safety inspection and tune-up on furnace and water heater in basement. Checked thermostat functionality (confirmed operating at 71° with 31% humidity) and inspected water heater connections including copper piping. Both systems functioning properly; no issues identified during preventative maintenance service.

Diagnosed and repaired a less than 5-year-old tanked water heater that was not producing hot water. Inspection of the basement-installed unit revealed issues with the heating elements, which were replaced to restore proper functionality.

Completed installation of a complete HVAC system including a 70,000 BTU furnace, 2.5 TON AC unit, condensate pump, and Honeywell HOME digital programmable thermostat. System was properly connected to existing ductwork with all mechanical and electrical components installed according to code requirements, and necessary permits were obtained for the installation.

Performed inspection of existing natural gas furnace system in basement, which is over 10 years old but currently operational. Documented current installation configuration including ductwork, PVC venting/drainage pipes, and connection points. Provided replacement estimate for aging furnace system with detailed documentation of existing plumbing infrastructure and electrical connections necessary for proper equipment installation.

Successfully installed a 70,000 BTU furnace with humidifier, liner, and dual PVC venting system. Completed all mechanical and electrical connections, including proper condensate drainage setup. System was fully tested and is operating within manufacturer specifications.

Successfully completed a two-day installation of a complete Lennox HVAC system, including a 90,000 BTU furnace, 3-ton air conditioner, S40 thermostat, and supplementary components (humidifier, APCO UV air purifier, and condensate pump). System features proper PVC venting with intake/exhaust pipes and includes a chimney liner installation. All ductwork connections were properly sealed and the system was fully tested for optimal performance.

Responded to no-heat call for 5-year-old boiler that was completely non-operational. Inspection revealed loose electrical connector at the control board terminal which had become disconnected. Reconnected terminal properly, tested system operation, and confirmed boiler now functioning correctly.

Responded to service call for Rheem tankless water heater displaying error code 88 with no hot water output. Inspected remote connection assembly and removed filter screen for cleaning. Performed descaling procedure on heat exchanger and verified proper operation of hot/cold water lines and gas connection. System functioning normally after service with no error codes present.

Replaced non-functional thermostat with customer-provided unit after diagnosing complete display failure and system non-operation. Installed new thermostat with proper wire connections and verified proper system operation for both heating and cooling functions.

Responded to no heat call for 10+ year old Goodman furnace located in basement. Upon inspection, performed diagnostic testing and discovered dirty air filter causing restricted airflow. Replaced filter, tested system operation through complete heating cycle, and verified proper temperature output at registers.

Returned to address no heat issue identified in previous service call. Diagnosed damaged and incorrectly wired RDS (Remote Data Sensor) device that had been recently installed. Documented condition with photos of circuit board and control panel wiring issues. Parts department has been notified to order replacement device; customer will be contacted regarding scheduling and pricing for follow-up repair.

Performed tune-up service on aging furnace (10+ years old) with significant rust and corrosion observed on heat exchanger components. Inspected and cleaned interior mechanical elements, including control boxes and valve actuators that showed dust accumulation and wear. Completed comprehensive system evaluation including thermostat, humidifier, and relatively new hot water tank (<1 year old) as part of preparation for home daycare operation.

Performed evaluation of aging gas furnace in basement showing significant noise issues during operation. Unit appears functional but at end of service life, with visible wear on ductwork connections and potential efficiency concerns. Replacement quote provided for new high-efficiency system that would address noise concerns and improve overall heating performance while maintaining compatibility with existing ductwork configuration and nearby water heater installation.

Conducted Gold Boiler Inspection on hot water boiler over 10 years old located in basement. Inspection confirmed properly functioning unit with clean, blue flame pattern across heat exchanger tubes indicating good combustion. System is operational with no immediate service needs identified.

Completed tankless water heater repair service as specified in the approved service estimate. Performed diagnostic assessment of the unit, which showed issues with internal components including circuit board and wiring connections. Repaired system according to manufacturer specifications and verified proper operation before completing service.

Responded to service call for waste pipe issue in 98-year-old home. Inspected plumbing infrastructure in basement where problem had been gradually developing. Identified and cleared blockage in the drainage system, verifying proper flow through the main vertical PVC pipe and its Y-junction connections to ensure full functionality of the waste pipe system.

Responded to service call for steam pipe with holes in basement. Upon inspection, discovered significant corrosion and multiple perforations in the aging galvanized steam line running along ceiling joists. Replaced damaged section of pipe, ensuring proper connections and sealing to prevent future leaks.

Conducted diagnostic assessment for potential radiator installation in basement and ceiling areas. Evaluated existing plumbing infrastructure including horizontal piping with brass fittings and valves. Documented current ventilation systems and space constraints to provide comprehensive estimate for customer-provided radiators.