Heating and Cooling Grosse Pointe Woods

Performed comprehensive furnace and air conditioning inspection on 2024 equipment located in basement. Completed full system diagnostics using Fieldpiece SC680 clamp meter to verify electrical parameters, amperage draws, and voltage readings across all components. Inspection included thorough evaluation of humidifier operation, thermostat functionality, and hot water tank condition per customer request, with all systems found operating within manufacturer specifications and photographic documentation captured for service records.

Completed installation of 2.5-ton air conditioning system with matching evaporator coil on left side of residence. Reconnected all electrical and refrigerant lines, verified thermostat operation and system functionality, and confirmed proper equipment communication. Mechanical, electrical, and air conditioning permits were requested and system was tested to ensure optimal performance upon startup.

Performed comprehensive tune-up and inspection on 5-year-old furnace located in basement and 15-year-old air conditioning unit located outside as part of late season maintenance special. Conducted electrical diagnostics using clamp meter, measuring amperage draw and testing hot surface igniter which registered 7389 ohms resistance, confirming proper operation within manufacturer specifications. Completed full system evaluation including visual inspection of both heating and cooling equipment, verified all electrical connections, and confirmed all components functioning properly with no immediate repairs required.

Responded to a water leak complaint on a furnace system under 10 years old located in the basement. Upon inspection, identified active water accumulation in the drain pan and corrosion on metal components, with moisture present around copper piping connections to the furnace. Assessed the condensate drainage system and associated plumbing connections, documented conditions with photographic evidence, and addressed the leak source under warranty coverage.

Completed comprehensive furnace tune-up and safety inspection on 10+ year old unit located in basement. Performed thorough examination of gas valve assembly, ignition control module with operational indicator light, electrical connections, and all safety controls. Inspected burner assembly, heat exchanger, blower components, and verified proper operation of all system functions. All components found to be in normal operating condition with no immediate safety concerns identified. System operating within manufacturer specifications.

Responded to service call for missing condensation pump from humidifier system. Upon inspection of basement-located HVAC air handler unit, confirmed that condensate pump assembly was not present at equipment. Documented existing installation showing air handler with standard condensate drain piping configuration using white PVC with proper joints and elbows, but lacking dedicated humidifier condensate pump component. Photographed current system setup including visible drainage lines, electrical connections, and equipment placement for warranty documentation purposes.

Completed comprehensive Gold AC inspection on a 10+ year old single-unit residential air conditioning system with air handler located in basement. Performed thorough visual and operational assessment of outdoor condenser unit, confirming proper fan operation and adequate airflow through louvered panels. Inspected electrical control panel and internal components including circuit boards, capacitor (45/5 MFD), transformers, relay boards, and control modules. Verified all electrical connections, wiring integrity, and proper component function. System operational and performing within normal parameters at time of inspection.

Completed installation of a 40-gallon short Bradford White tank water heater in basement utility area. Performed mechanical connections including copper supply piping with brass fittings, installed red-handled ball valve on hot water outlet, and mounted pressure relief valve on top of tank. Unit was positioned on checkered tile floor with white drain pan at base and reconnected all plumbing connections per manufacturer specifications and code requirements.

Responded to service call for toilet not flushing properly in residential bathroom. Upon inspection, diagnosed issue with flush mechanism and performed necessary repairs to restore proper flushing function. Tested unit multiple times to ensure complete resolution and verified all components operating correctly.

Completed on-site assessment for sump pump installation in basement of 1950s-era residential property. Evaluated existing plumbing infrastructure and provided estimate for new sump pump system, backflow prevention valve/assembly replacement, and interior sprinkler system capping. Documented existing PVC drainage line configuration mounted to basement cinder block wall for reference in final installation specifications.

Completed full HVAC system installation including 70,000 BTU furnace and 3-ton air conditioning unit with right-side configuration. Installation included S40 thermostat, humidifier, condensate pump, duct liner, and reconnection of existing electronic air cleaner after verification. Obtained mechanical and electrical permits, positioned outdoor condenser unit on concrete pad against building exterior, and ensured system qualifies for utility rebate program under AHRI certificate 216722046.

Installed small bypass humidifier to improve indoor air quality and maintain proper humidity levels throughout the home. Verified furnace operation and proper flame characteristics during system testing to ensure safe and efficient integration with existing HVAC equipment.

Completed plumbing service call for bathroom fixture maintenance. Inspected undermount sink installation with chrome drain assembly beneath granite vanity countertop, verified proper drainage function and seal integrity. All fixtures operating within normal parameters upon completion of service visit.

Responded to no heat call for back end of residential property. Inspected 2-year-old furnace located in basement to diagnose insufficient heat distribution to rear zones. Performed system diagnostic to identify cause of uneven heating and restore proper airflow to affected areas.

# Plumbing Service - Clogged Drain/Sink Responded to a main drain backup issue affecting the kitchen drainage system. Upon arrival, found the main drain line was experiencing blockage causing water to back up when kitchen fixtures were in use, while bathroom drains remained functional. Inspection revealed significant water damage on the basement floor with standing water and staining patterns indicating recent overflow events. Located the main drain cleanout access point in the basement utility area near the plumbing assembly. Assessed the drainage system configuration including vertical stack pipes and horizontal drain lines. Utilized drain cleaning equipment to clear the obstruction in the main line. Successfully restored proper drainage flow to the kitchen plumbing system. Verified clearance by running water through kitchen fixtures and confirming no backup occurred. Advised on the existing water damage conditions observed in the basement and recommended monitoring for future drai

Responded to emergency water pump failure in 1947 residential property affecting hydronic heating system. Upon arrival, assessed damaged circulator pump that had overheated, causing smoke and thermal damage to adjacent water heater components. Replaced failed circulator pump with new unit, installed on plywood mounting panel alongside existing pump in dual-zone configuration. Reconfigured copper and brass piping network to accommodate new pump installation, including integration with existing PEX tubing distribution lines. Installed new shut-off valves with red wheel handles at strategic control points throughout the system for proper isolation capability. Verified all brass fittings and couplings were properly secured and leak-free. Tested both circulation pumps for proper operation and flow direction. Confirmed electrical connections were secure and properly grounded. System pressurized and tested for leaks at all connection points. Verified proper operation of all zone valves and sh

Completed comprehensive spring maintenance on 10-year-old air conditioning system located on west side of property. Performed full AC tune-up including inspection of outdoor condensing unit electrical components, capacitor testing, contactor examination, and control board verification. Inspected indoor air handler unit, confirmed 20x25x4 filter specifications for Mitsubishi system, checked electrical connections and wiring integrity throughout system, and utilized diagnostic meters to verify proper amperage draws and system performance. All components found operational and system ready for cooling season.

Responded to no heat call for furnace located in upstairs bedroom closet. Upon inspection, found unit powering on but failing to produce adequate heat. Accessed blower assembly and discovered significant dust accumulation on centrifugal fan blades and housing components affecting airflow efficiency. Inspected electrical connections and wiring harness, confirming all wire terminals and connectors were secure with no visible damage. Examined inducer motor assembly and verified proper operation. Cleaned blower wheel and housing to restore optimal air circulation. Checked all safety controls and limit switches for proper function. System tested and confirmed return to normal heating operation with proper temperature rise across heat exchanger.

Responded to no-heat call where thermostat displayed error code on 14-year-old furnace located in basement. Diagnosed failed heat exchanger requiring full unit replacement. Provided comprehensive replacement estimate and documented exterior conditions including chimney requiring possible new liner and existing PVC vent termination through brick wall.

Responded to no-heat call on 14-year-old furnace displaying thermostat error code. Performed diagnostic inspection using borescope camera to examine heat exchanger and internal components for cracks, corrosion, and blockages. Inspected blower wheel assembly and found moderate dust accumulation on blades affecting airflow efficiency. Cleaned blower wheel, verified proper operation of all mechanical and electrical components, cleared error code, and restored heating system to normal operation.