Heating and Cooling Grosse Pointe Woods

Responded to a plumbing service call for bathroom sink maintenance. Upon inspection, serviced a traditional two-handle chrome faucet and white porcelain sink assembly. Verified proper operation of the drain stopper mechanism and inspected the P-trap assembly beneath the sink, confirming all PVC drain connections and chrome tailpiece were secure and leak-free. Checked both hot and cold water supply lines with mounting brackets for proper connection to the faucet assembly. All plumbing components were found to be in standard working condition with no visible leaks or damage detected.

Responded to no cooling complaint on six-year-old Trane commercial rooftop unit. Upon inspection, diagnosed failed control board causing system malfunction. Replaced defective control board with OEM replacement part under existing purchase order, verified all electrical connections, and tested system operation. Unit restored to full cooling capacity with proper airflow and temperature differential confirmed.

Conducted comprehensive site assessment for complete HVAC system replacement at residential property. Evaluated existing outdoor condensing units showing significant age-related deterioration, dirt accumulation, and weathering on exterior panels. Documented current dual-unit configuration positioned on concrete pads in side yard location. Inspected interior ductwork system and plenum, noting recent electrical line installation along main trunk line. Photographed existing equipment conditions and infrastructure to support full system replacement proposal. Provided detailed quote for new HVAC system installation including equipment specifications and labor requirements.

Completed comprehensive Gold Furnace Inspection as part of complimentary spring tune-up service for 12-year-old heating system located in basement. Performed full system evaluation including visual inspection of furnace components, heat exchanger examination, burner assembly assessment, and verification of all safety controls and limit switches. Cleaned and inspected blower assembly, checked belt tension and condition, and lubricated motor bearings as needed. Tested ignition system operation, verified proper flame characteristics, and measured temperature rise across heat exchanger to ensure efficient operation. Inspected venting system for proper draft and secure connections, checked condensate drain for blockages, and verified all electrical connections were tight and secure. Replaced air filter and cleaned flame sensor to optimize performance. Tested thermostat operation and calibration, confirmed proper system cycling, and documented all operational parameters within manufacturer s

Completed furnace replacement estimate for basement installation with equipment age exceeding 10 years. Assessed existing gray metal cabinet furnace unit with horizontal ductwork and galvanized metal plenum connections. Documented current system configuration including ductwork transitions, utility room layout, and equipment accessibility for replacement planning. Photographed installation area showing concrete block walls, concrete flooring, and proximity to water heater to determine clearance requirements and proper equipment sizing for future replacement.

Completed comprehensive Gold-level furnace inspection on a 2-year-old forced air heating system located in the basement. Performed thorough visual examination of all accessible components including heat exchanger, burner assembly, blower motor, and electrical connections. Inspected condensate pump and drainage system, verified proper operation of all safety controls, and examined ductwork connections. Documented equipment condition through photographic records showing internal components and overall system installation. All components found operating within normal parameters with no immediate service needs identified.

Completed full HVAC system installation including a 110,000 BTU gas furnace with right-side configuration and 4-ton air conditioning unit in residential mechanical room. Installed Aprilaire humidifier mounted on furnace, new thermostat, and 20x25x1 filter base with 600 CFM airflow capacity. Ran new PVC venting and drainage lines, connected copper refrigerant lines, and installed metallic ductwork with proper segmented joints. Mounted exterior electrical disconnect and established utility meter connections on exterior brick wall. Reconnected all necessary gas, electrical, and plumbing connections. Obtained mechanical and electrical permits and remeasured return air for proper system sizing. System qualified for utility rebate program and passed all code inspections.

Completed comprehensive Gold Furnace Inspection on a 13-year-old Bryant forced air heating system located in the basement. Performed full system evaluation including visual inspection of furnace cabinet, ductwork, and humidifier control components. All equipment found to be in operational condition with humidifier control panel functioning properly and ductwork showing no signs of deterioration or damage. Documentation photos captured for service records.

Completed comprehensive tune-up on 4-year-old furnace located in basement. Performed full system inspection including blower motor assembly, electrical connections, and all internal components. Per customer request, inspected and evaluated pump system; verified proper operation and found all equipment functioning within normal parameters with no issues identified.

Completed comprehensive tune-up and safety inspection on furnace over 10 years old located in basement for city inspection compliance. Verified proper ignition sequence and burner flame characteristics, confirmed all gas connections secure with no leaks detected, and inspected heat exchanger for integrity. Tested all safety controls including limit switches and flame sensor, cleaned burner assembly, checked and adjusted gas pressure, and verified proper venting and combustion air supply. System operating safely and efficiently within manufacturer specifications; all components functioning properly with no immediate concerns noted.

Completed comprehensive tune-up and city inspection preparation on 8-10 year old gas furnace located in basement. Performed full system evaluation including burner assembly operation verification, heat exchanger inspection, blower motor assessment, electrical connection testing, and ductwork examination. All components found operating within normal parameters with burner flames showing proper blue combustion pattern and system controls functioning correctly.

Responded to service call regarding recently installed electrical outlet for stove connection. Inspected existing outlet mounted on concrete block wall and discussed rotating receptacle 90 degrees to accommodate appliance cord orientation. Documented current installation with photographs showing outlet box properly secured to wall with cord connected and verified electrical functionality prior to any modifications.

Completed installation and startup of Lennox model ML13KC1-030-230A04 air conditioning system with R-454B refrigerant. Unit was properly mounted on a black pad with gravel base, with all refrigerant lines and electrical connections secured according to manufacturer specifications. System was successfully tested and is operating within normal parameters.

Performed comprehensive inspection of residential property to assess GFI outlet requirements. Utilized Klein voltage tester to evaluate multiple outlets throughout the home, identifying areas requiring code-compliant GFI protection. Provided homeowner with recommendations for necessary electrical safety upgrades to ensure compliance with current electrical codes.

Performed comprehensive tune-up on dual HVAC system with units located in attic and basement. Inspected furnace operation, observing proper flame pattern in gas burner assembly (3 burners with consistent blue flames) and checked electrical components including blower motor assembly and wiring connections. Noted system was operational but recommended regular cleaning due to visible dust accumulation on internal components.

Performed tune-up service on 2018 HVAC system located in basement. Conducted comprehensive diagnostics using Testo 510 digital meter, recording temperature readings of 56°C and pressure/gas measurements of 729 ppm. Inspected and verified proper functioning of humidifier, thermostat, and hot water tank as part of routine maintenance protocol.

Performed routine tune-up on gas furnace of undetermined age. Conducted combustion analysis using Fieldpiece digital meter to verify proper operation. Inspected burner assembly which displayed appropriate blue flame pattern, indicating efficient combustion and proper gas-air mixture. All components functioning normally with no issues detected.

Responded to service call for a 2-year-old furnace reported with incorrect power interrupt installation, failing inducer motor, and leak. Inspection confirmed inducer motor drawing 0.26 amps, which is below normal operational parameters. Visual examination revealed significant corrosion and rust on internal components, consistent with reported leak issue. Documented findings with detailed photos of affected components and electrical measurements for service record.

Accessed plumbing system through wall access panel to inspect copper supply line and mounting bracket. Performed maintenance on bathtub/shower fixture with blue tile surround, ensuring proper function of chrome faucet, controls, and drain.

Completed service call for sold repair of electrical system. Inspected main circuit breaker panel, verified proper operation of breakers and indicator lights. Installed new electrical outlet with proper grounding near gas line connection point.