HVAC, Plumbing and Electrical in Detroit

Responded to service call for surge protector installation on HVAC system equipment. Successfully installed and wired new surge protection device to electrical junction box serving motor and control components. Verified proper electrical connections, tested system operation, and confirmed all mechanical and electrical components functioning correctly with new surge protection in place.

Responded to emergency call for leaking hot water tank in basement with water discharge from bottom of unit. Upon inspection, determined tank had failed and required complete replacement due to irreparable leak at base. Disconnected and removed existing failed water heater, including all supply lines, discharge piping, and electrical connections. Installed new tanked water heater with proper venting, connected hot and cold water supply lines with appropriate shut-off valves, and installed temperature and pressure relief valve with proper discharge piping termination. Reconnected all plumbing connections using code-compliant materials and methods, ensuring proper clearances around unit for maintenance access. Tested all connections for leaks, verified proper water flow and heating operation, and confirmed system functionality before completing installation. Unit now operating within normal parameters with no active leaks detected.

Responded to a partially clogged kitchen sink drain in a 1960s single-family home where water was draining slowly and backing up after initial flow. Accessed the drain system through the cabinet beneath the sink and inspected the P-trap and drain pipe assembly. Removed the existing P-trap components and cleared accumulated debris and buildup causing the blockage. Verified that other household drains were functioning properly, confirming the clog was isolated to the kitchen sink line. Reassembled the drain system with proper connections, tested water flow to ensure complete drainage without backup, and confirmed the issue was fully resolved. Left work area clean with all plumbing fixtures operating normally.

Installed a 40-gallon Bradford White tanked water heater in basement utility room, completing all copper piping connections for inlet and outlet lines with appropriate valves and fittings. Permit was requested for the installation, and the unit was properly secured and vented according to manufacturer specifications and local code requirements.

Responded to commercial furnace service call and inspected HVAC system components in basement mechanical room. Upon arrival, observed existing condensate pump assembly mounted on copper piping with associated heat exchanger components, all showing signs of age and normal operational wear. Documented equipment condition with photographs for service records.

Responded to service call for commercial rooftop furnace with broken belt. Accessed roof using ladder and located unit among multiple HVAC systems on flat membrane roof. Removed failed belt and installed replacement belt, ensuring proper tension and alignment. Tested unit operation to verify proper function and airflow. Unit restored to full operational status.

Responded to non-functioning water heater in basement. Upon arrival, inspected 5-year-old tanked water heater with Defender Safety System. Diagnosed failed pilot assembly preventing burner ignition. Replaced defective thermocouple and cleaned pilot orifice. Tested gas control valve operation and verified proper gas flow through yellow-handled shut-off valves. Relit pilot light, confirmed burner ignition, and verified proper venting through exhaust flue. Unit restored to full operational status with hot water production confirmed.

Provided comprehensive estimate for complete HVAC system replacement including air conditioning unit and furnace equipment. Assessed existing interior mechanical room configuration with current furnace/air handler and water heater setup, evaluating ductwork connections, venting requirements, and electrical service capabilities at exterior meter location. Documented equipment specifications and site conditions to prepare detailed replacement proposal for residential comfort system upgrade.

Responded to commercial flower shop for non-operational garbage disposal unit. Upon arrival, performed diagnostic assessment of disposal system beneath stainless steel single-basin sink. Tested electrical connections, reset switch, and verified power supply to unit. Determined disposal motor had seized due to jamming or mechanical failure. Cleared any debris from grinding chamber, attempted manual reset using Allen wrench access point at bottom of unit, and verified breaker panel status to rule out electrical issues.

Responded to service call for commercial furnace system located in basement mechanical room. Upon arrival, inspected 10+ year old heating system and associated hydronic components including 4900 Series Air Separator and connected copper piping. Performed diagnostic evaluation of furnace operation, examined air handler unit, verified proper function of water heater and flue connections, and assessed condition of manifold system and related plumbing components. All equipment photographed and documented for service records.

Responded to main drain clog affecting multiple basement fixtures including floor drain and toilet. Successfully cleared main line obstruction restoring proper drainage throughout the basement plumbing system. Additionally provided detailed assessment and quote for basement water line replacement for insurance documentation purposes.

Completed two-day air handler installation in attic space with associated condenser unit on exterior deck. Installed new air handler with insulated ductwork connections, control module, condensate pump, drain pan, and wet switch. Installed outdoor condenser unit with electrical disconnect box, verified all refrigerant connections, tested system operation, and confirmed proper drainage. Obtained mechanical and electrical permits for installation and reconnection work, performed final system checkout including airflow measurements for utility rebate qualification.

Completed comprehensive Gold Plan AC inspection on Daikin split system with attic-mounted horizontal air handler and exterior condenser unit. Performed full system evaluation including visual inspection of indoor air handler components, ductwork connections, electrical connections, and condensate management in attic location. Inspected outdoor condenser unit for proper operation, cleared debris from surrounding area, verified adequate clearances, examined electrical disconnect and power supply connections at exterior wall. All system components found operating within normal parameters with no immediate service needs identified at time of inspection.

Responded to warranty service call for newly installed boiler system experiencing fluid accumulation in vent pipe and reduced water pressure. Upon inspection, identified improper PVC venting termination and configuration issues on exterior brick wall. Corrected boiler exhaust and intake venting system by installing 2" PVC pipe and 90-degree elbow fittings to achieve proper termination height and positioning. Verified proper condensate drainage, restored adequate system water pressure, and confirmed all venting meets manufacturer specifications and code requirements for safe operation.

Completed full HVAC system installation including Lennox 70,000 BTU furnace and 2-ton air conditioning unit in rear yard location. Installed new thermostat, condensate pump, and ductwork with liner, performed all mechanical reconnections, and coordinated electrical work. Mechanical and electrical permits obtained, system registered for utility rebate program with AHRI certificate 21558456, and all equipment labeled and documented per code requirements.

Provided estimate for water heater replacement in basement. Existing unit over 10 years old with active leak underneath, rendering it inoperable. Assessed current installation including all plumbing connections, hot and cold water lines, copper tubing, and associated pipe fittings to determine replacement specifications and requirements.

Conducted estimate for complete air conditioning system replacement at residential single-family home. Inspected existing 10-year-old system components located in attic space, including air handler unit, ductwork configuration, and plenum connections. Documented current installation featuring insulated flex duct runs, vertical supply plenum with reflective wrap insulation, and existing support structure. Evaluated attic access conditions, workspace constraints, and structural framing for new equipment installation. Photographed existing HVAC infrastructure including duct connections, insulation materials, and equipment positioning to assess replacement requirements and determine proper sizing for new system components.

Completed toilet replacement in residential bathroom. Removed existing fixture and installed new one-piece toilet unit supplied by customer. Ensured proper sealing, secure mounting to hexagonal tile floor, and verified all connections for proper operation and leak-free performance.

Provided estimate for complete steam boiler replacement due to flood damage and age-related deterioration of existing 10+ year old unit. Existing boiler system showed extensive corrosion, rust staining, and water damage throughout, rendering equipment beyond economical repair. Deteriorated chimney structure exhibited significant brick damage and structural compromise requiring attention during replacement process.