Heating and Cooling Ferndale

Performed pre-season inspection and system evaluation on 10+ year old forced air furnace located in basement that had been inactive for an extended period. Conducted comprehensive operational assessment of furnace components, verified gas supply connections, inspected blower assembly, and tested electrical systems and controls. Documented existing equipment conditions including American ProLine water heater and ductwork configuration, with blower motor replacement parts previously ordered from Trane and confirmed available for installation upon customer approval.

Completed installation of 40-gallon standard residential water heater at property. Properly connected all water supply lines, installed temperature and pressure relief valve, and verified all plumbing connections for leak-free operation. System tested and confirmed operational with adequate hot water delivery throughout the residence.

Completed comprehensive Gold Furnace Inspection on 3-year-old forced air system located in basement. Performed thorough inspection of all furnace components, including flame sensor cleaning and verification. Inspected and documented Honeywell Home 16x25x4 air filter (Model FC100A1029, MERV 11 rating) currently installed in system. All equipment found operational and functioning within normal parameters at time of inspection.

Performed pre-season inspection on 10+ year old forced air furnace located in basement that had been inactive for an extended period. Conducted comprehensive system check including blower motor assembly, electrical connections, and overall operational components. Inspected blower motor with cooling fins, verified wire connections, and assessed mounting bracket which showed age-related corrosion consistent with older equipment. System cleared for operation and ready for heating season.

Completed furnace inspection for city certification on 7-year-old unit located in basement. Performed comprehensive tune-up including visual inspection of all components, tested safety controls and limit switches, verified proper combustion and heat exchanger integrity, cleaned burner assembly, checked and adjusted gas pressure, inspected flue venting system, replaced air filter, and confirmed thermostat operation showing proper cooling setpoint at 68°F. All systems found operating within manufacturer specifications and meeting city code requirements for rental property certification.

Performed scheduled filter change on single rooftop unit at commercial facility. Accessed RTU via roof using lift equipment. Removed two pleated air filters from horizontal mounting frame within air handler compartment and replaced with new filters of matching specifications. Verified proper installation of filters with securing clips and confirmed adequate seal within filter tracks.

Completed comprehensive Gold-level furnace inspection and tune-up on a 10-year-old forced air heating system located in the basement as part of the Flame Fixed Membership plan. Performed standard maintenance protocol including visual inspection of all internal components, burner assembly, heat exchanger, blower motor, electrical connections, and safety controls. Verified proper operation of ignition system, flame sensor, and pressure switches. Inspected condensate drain lines and PVC venting for proper drainage and clearance. Tested system startup and shutdown sequences to ensure safe and efficient operation. All components found to be functioning within manufacturer specifications with no immediate repairs required. System is ready for the upcoming heating season.

Completed Gold Furnace Inspection for city compliance requirements. Performed comprehensive examination of heating system components including internal blower motor assembly, electrical connections, control board functionality, and safety mechanisms. Documented equipment condition with photographic evidence showing furnace interior with properly secured wire harnesses, operational control board with LED indicators, and all electrical connections intact. Also inspected and documented water heater installation in mechanical room, noting existing floor moisture staining around base indicating previous water discharge or condensation issues that should be monitored. All furnace components verified to be in working order with no immediate safety concerns identified during inspection. System passed visual and operational assessment for city inspection purposes.

Completed comprehensive furnace inspection and tune-up on forced air heating system located in laundry room. Removed access panel and performed thorough examination of all internal components including blower motor assembly, electrical connections, wiring harnesses, control module, and condensate management system. All terminal connections, wire nuts, and color-coded wiring confirmed secure and properly configured per manufacturer specifications, with unit showing normal operational condition and standard safety mechanisms functioning as designed.

Performed follow-up inspection of AO Smith tanked water heater for municipal certification purposes. Conducted comprehensive examination of unit installation, including verification of proper venting system configuration with metallic exhaust duct routing, assessment of all plumbing connections including copper supply lines and valve assemblies, and confirmation of safety label compliance. Documented water heater condition and installation in utility room setting where property occupant had previously removed appliances and wall materials to facilitate access. Verified all components meet code requirements for certification approval.

Completed comprehensive tune-up and safety inspection on two residential furnace units, one located in basement and one in attic. Performed full system diagnostics on both units including gas valve operation, blower motor function, electrical connections, and heat exchanger inspection. All components tested within normal operating parameters, burners cleaned, filters checked, and both systems certified for safe operation per city requirements.

Completed comprehensive annual Gold-level furnace inspection on 4-year-old unit located in basement. Performed full system evaluation including visual inspection of gas valve assembly, burner manifold, pressure switches, electrical connections, and control components. Verified all wiring connections at terminal block, inspected capacitor, condensate pump assembly, and safety controls for proper operation. All components found in good working condition with no deficiencies noted. System operating within manufacturer specifications with no repairs required at this time.

Completed comprehensive Gold Plan furnace inspection on 10-year-old basement unit. Performed full system tune-up including burner assembly examination, gas valve inspection, ignition system check, electrical connection verification, and pilot assembly assessment. All components operating within normal parameters with no deficiencies identified; unit requires no repairs at this time.

Completed furnace inspection and replacement estimate for 35-year-old forced air heating system located in basement. Upon assessment, found aging equipment with deteriorated ductwork showing surface oxidation and outdated metal plenum assembly with dimpled surface construction. Provided comprehensive replacement recommendations for residential HVAC system upgrade based on equipment condition and age exceeding typical service life expectancy.

Completed annual Gold Furnace Inspection on one-year-old unit located in basement as part of preventative maintenance service plan. Performed comprehensive tune-up including visual inspection of all internal components, gas valve assembly, electrical connections, and control modules. Conducted combustion analysis testing using Testo 310 analyzer to verify proper burner operation and efficiency levels. All systems operating within manufacturer specifications with no deficiencies noted.

Performed comprehensive furnace inspection and tune-up on 35-year-old forced air heating system located in basement. Inspected control board wiring, verified proper electrical connections at terminal blocks, and confirmed green status LED indicator functioning correctly. Evaluated low-voltage control wiring including thermostat connections, examined flexible metallic conduit for electrical protection, and assessed overall system operation to ensure safe and efficient performance for the heating season.

Corrected code violation where A/C disconnect was improperly fed with NM-B (Romex) cable, which is not rated for exterior applications. Replaced non-compliant wiring with appropriate exterior-rated conduit and conductors to bring installation up to NEC standards and ensure safe, weather-resistant operation of the air conditioning disconnect switch.

Completed comprehensive Gold-level furnace inspection and tune-up on a 2-year-old unit with no reported operational issues. Performed full system evaluation including visual inspection of internal mechanical components, burner assembly, heat exchanger, blower motor, and all electrical connections. Verified proper operation of all safety controls, ignition system, and flame sensors. Inspected and confirmed secure routing of all gas lines, condensate drainage system, and venting components. All wiring harnesses, control boards, and restart safety devices found in proper working condition with no signs of wear or deterioration. System operating within normal parameters with no deficiencies noted.

Responded to report of water leaking from 2-year-old furnace in basement. Upon inspection, identified condensate drain issue causing water accumulation. Cleared condensate line blockage, verified proper drainage flow, and tested system operation to ensure leak was resolved and unit functioning correctly.

Completed comprehensive gold-level furnace maintenance inspection on Goodman unit located in crawlspace. Performed full system diagnostic including combustion analysis using digital flue gas analyzer, which confirmed safe operating parameters with oxygen levels at 8.5%, carbon monoxide at 78 ppm, efficiency at 84.9%, and flue temperature at 245°F. Inspected all internal components including blower motor assembly, electrical connections, control boards, and ductwork connections; all components found in satisfactory working condition with normal dust accumulation for age of unit.