Heating and Cooling Hazel Park

Responded to emergency call for major gas leak on commercial furnace unit located in high bay area. Utilized lift equipment to safely access elevated furnace installation. Located source of gas leak in supply line connection above furnace cabinet. Isolated gas supply, performed leak detection procedures, and secured affected connections. Conducted pressure testing to verify system integrity and confirmed no additional leak points present upon completion of repairs.

Completed full HVAC system installation including new furnace, air conditioning unit, condensate pump, and programmable thermostat. Verified and installed correct evaporator coil model CK40CT-24A-71 as specified. Updated electrical panel with appropriate circuit breakers for new equipment, applied for required permit, and submitted documentation for utility rebate program.

Completed comprehensive assessment of non-functional R22 central air conditioning system experiencing fan motor failure. Evaluated existing equipment and determined system required outdoor fan motor, capacitor, and contactor replacement. Due to age of R22 system and availability of refrigerant, provided detailed estimate for complete HVAC system replacement including new air handler and condensing unit. Documented existing ductwork configuration and mechanical installation area for replacement specifications.

Responded to service call for leaking water heater in basement utility area. Upon inspection, found existing 40-gallon residential tank-style water heater with active leak at base and visible water damage on concrete floor surrounding unit. Water supply had been shut off to unit prior to arrival. Assessed unit for potential repairs but determined leak originated from tank failure, rendering unit non-repairable. Provided estimate for replacement and received approval to proceed with same-day installation. Removed failed water heater and prepared installation area. Installed new 40-gallon residential gas-fired tank water heater in same location. Connected cold water supply line and hot water outlet using appropriate copper piping and fittings. Installed temperature and pressure relief valve with proper discharge piping termination. Connected existing gas line using flexible gas connector with yellow coating, ensuring all connections met code requirements. Verified proper venting configu

Responded to service call for air conditioning unit that would not turn on. Upon inspection, accessed attic space to evaluate approximately 10-year-old system with evaporator coil located in basement. Examined HVAC ductwork system with foil-backed insulation in attic area and inspected blower motor assembly with associated wiring and connections. Assessed system components including ductwork access points, electrical connections, and mechanical assemblies to determine equipment condition and provide replacement estimate for non-operational air conditioning system.

Responded to no cooling call on 10-year-old air conditioning system with evaporator coil located in basement. Upon arrival, confirmed unit would not power on. Performed electrical diagnostics using clamp meter at outdoor condenser unit to test voltage and amperage at compressor and fan motor connections. Inspected condenser coil for debris accumulation and airflow restrictions. Identified failed component preventing system startup and advised homeowner of necessary repairs to restore cooling operation.

Completed furnace replacement estimate for 26-year-old Luxaire heating system located in basement. Assessed existing equipment including furnace unit with flexible metallic ductwork connections and adjacent gray metal air handler with plenum assembly. Evaluated smart thermostat compatibility and provided comprehensive replacement quote for aging HVAC system.

Conducted on-site evaluation for complete HVAC system replacement including non-operational air conditioning condenser unit located on exterior concrete pad and natural gas furnace installed in basement. Assessed existing equipment configuration, documented current system conditions through photographic inspection, and gathered necessary specifications to prepare comprehensive replacement estimate for both heating and cooling components.

Completed comprehensive Gold AC Inspection on 6-year-old residential air conditioning system with air handler located in basement. Performed full system evaluation including visual inspection of outdoor condensing unit, refrigerant lines, electrical disconnect, and filter components. Advised customer that condenser area requires clearing of surrounding debris and vegetation encroachment to maintain proper airflow and system efficiency. All major components operational at time of inspection, with system responding normally to thermostat commands and maintaining proper cooling cycle.

# HVAC Service Completed Responded to service call for central air conditioning system not cooling while heating function remained operational. Upon arrival, performed thorough inspection of outdoor condenser unit and found excessive dirt accumulation affecting system performance. Cleaned condenser coil fins and removed debris from unit exterior and surrounding area. Inspected electrical connections at terminal block and verified all wire connections were secure. Tested system operation after cleaning and confirmed proper cooling function restored. Unit returned to normal operating condition with adequate airflow through condenser fan assembly.

Responded to water leak originating from basement plumbing connected to toilet in 75-year-old residence. Located source of leak at pipe penetration point through floor joists where deteriorated sealing had failed. Repaired leak by securing pipe connection, applied expanding foam insulation around pipe penetration to seal gap and prevent future moisture infiltration, and verified proper drainage function to toilet fixture above. Confirmed no water damage to surrounding wooden framing and leak was successfully contained.

Completed comprehensive Gold Furnace Inspection on a 7-month-old forced air furnace and air conditioning system located in the basement. Performed thorough examination of all system components including control board, electrical connections, blower assembly, and outdoor condensing unit. All equipment found to be operating properly with no deficiencies noted; system confirmed in excellent working condition.

Performed comprehensive AC tune-up on 5-year-old residential cooling system that had not received maintenance since original installation in new construction. Cleaned condenser coils on outdoor unit, verified refrigerant charge within manufacturer specifications, inspected electrical connections and components, and confirmed proper system operation. All equipment found to be functioning normally with no deficiencies noted.

Assessed existing HVAC system in basement where homeowner was using duct tape to seal air filter during changes due to lack of proper filter box. Measured ductwork dimensions and evaluated air handler configuration to determine specifications for installing a permanent filter grille assembly. Provided estimate for proper filter box installation to eliminate need for temporary sealing methods and facilitate routine filter maintenance on the 5-year-old furnace system in this 2021 construction home.

Completed preventative maintenance tune-up on residential furnace unit located adjacent to kitchen area. Inspected and cleaned flame sensor rod, which showed signs of carbon buildup that could affect ignition reliability. Verified proper airflow through return air grille and checked system operation. Advised homeowner of need for carbon monoxide detector installation for safety compliance.

Performed seasonal start-up and operational verification on residential split-system air conditioning unit installed the previous week. Conducted comprehensive system diagnostics using calibrated digital instruments to measure and record operating parameters. Confirmed proper refrigerant charge levels, verified electrical connections, and ensured condensing unit was functioning within manufacturer specifications on exterior concrete pad installation.

Installed a 40-gallon Bradford White tanked water heater in basement utility area, connecting all necessary copper supply lines, discharge piping, and exhaust venting. Verified proper operation, tested temperature and pressure relief valve functionality, and ensured all connections were secure and code-compliant.

Responded to warranty call for newly installed system with possible contactor failure. Upon inspection, verified electrical connections at breaker panel and confirmed proper power supply to unit. Documented Siemens electrical components and circuit breaker configuration for service records.

Completed full installation of 2-ton air conditioning system with matching evaporator coil. Unit positioned on rubber mounting pad in exterior service access area adjacent to building structure. Installed electrical disconnect box with proper conduit routing from wall to equipment. Configured PVC condensate drainage system with pump assembly to handle moisture removal. All mechanical, electrical, and air conditioning permits obtained and work performed to code. Humidifier reconnected to system. System tested and operational.

Conducted on-site assessment for central air conditioning system installation at residential property. Evaluated existing utility room infrastructure, including current ductwork configuration, electrical service capacity at meter location, and available space for new equipment placement adjacent to water heater. Documented exterior wall access points and verified electrical service compatibility for new HVAC system requirements. Prepared comprehensive equipment replacement quote based on site conditions and customer cooling needs.