Heating and Cooling Waterford Township

Responded to call for water dripping from AC unit and ductwork at lower level. Inspected recently installed air conditioning system, approximately a few months old. Performed pressure differential testing using digital manometer, recording measurements of 0.61 and 0.58 inches of water column to diagnose drainage issue. Evaluated condensate drain line and ductwork for proper installation and flow. Identified and corrected drainage problem causing water intrusion into living space.

Responded to no cooling call on a three-year-old residential AC system located in utility room. Upon arrival, performed diagnostic evaluation of the system including electrical components, refrigerant pressures, and airflow verification. System was found operational during testing, with all components functioning within normal parameters and adequate cooling output restored to the entire home.

Responded to call back for hot tub breaker tripping issue. Upon arrival, inspected exterior electrical installation including breaker panel, meter enclosure, and associated conduit runs serving hot tub circuit. Documented existing electrical configuration with photos showing panel boxes, conduit routing, and connections on exterior wall near HVAC equipment. Troubleshot circuit to identify source of nuisance tripping and verified proper operation of hot tub electrical system.

Completed electrical panel installation and dedicated circuit wiring for new hot tub application. Installed new breaker panel with appropriate amperage rating, ran electrical cable from main service through wall cavity to hot tub location, and terminated all conductors per NEC requirements. All connections were properly torqued, circuit tested for continuity and proper voltage, and installation verified to be code-compliant and ready for hot tub connection.

Completed annual Gold AC inspection and seasonal start-up service for residential cooling system with indoor components located in basement. Performed comprehensive tune-up including condenser unit inspection, refrigerant level verification, electrical connection testing, and airflow assessment. All system components found operating within normal parameters with no deficiencies noted; unit prepared for cooling season operation.

Responded to no-cooling call on 2-year-old residential air conditioning system with non-operational outdoor fan. Diagnosed failed dual run capacitor on condenser unit located in backyard. Replaced defective capacitor with proper OEM replacement, restoring full system operation and verifying proper amperage draw on compressor and condenser fan motor.

Assessed utility area plumbing configuration for upcoming utility sink installation. Documented existing plumbing infrastructure including copper gas line distribution manifold, PVC drainage piping, and floor penetrations. Removed existing 24x20 tub from site and transported to shop for measurement verification to ensure proper replacement fixture ordering. Temporary drainage collection system remains in place with bucket under condensate line until utility sink installation is scheduled and completed.

Responded to service call for outdoor air conditioning condenser unit reporting slight operational noise. Inspected condenser unit located on exterior concrete pad, verified unit operation and assessed mechanical components for abnormal sounds. Examined condenser fan motor, compressor, and associated hardware for loose components or wear indicators. Documented equipment condition with photos showing outdoor condenser unit and indoor furnace plumbing connections in main level laundry room. Unit operational at time of inspection with age-related wear consistent with equipment over 10 years old.

Completed comprehensive Gold AC Inspection and tune-up on 11-year-old residential air conditioning system in preparation for summer season. Performed full preventive maintenance protocol on outdoor condensing unit including inspection of fan assembly, motor mount, electrical connections, refrigerant levels, and condenser coil cleaning. Unit operating within normal parameters with no immediate repairs required; documentation and photos captured for service records.

Successfully completed installation of a 2.5-ton Lennox air conditioning system with matching evaporator coil at residential property. Installed Lennox model CK40CT-30B-71 evaporator coil factory-equipped with TXV suitable for R-454B refrigerant. Positioned new condenser unit on concrete pad in rear yard with proper clearances and mounted securely. Ran and connected refrigerant lines from outdoor condenser to indoor coil using proper brazing techniques. Completed all electrical connections and reconnected system to existing power supply. Evacuated system, charged with appropriate refrigerant per manufacturer specifications, and verified proper operating pressures and temperatures. All mechanical, electrical, and air conditioning permits were obtained prior to installation. System tested and operational upon completion.

Successfully completed installation of a 2.5-ton Lennox air conditioning system with evaporator coil at residential property. Positioned new condenser unit on rubber isolation pad with gravel base against rear exterior brick wall, installed electrical disconnect box and conduit with proper wiring connections to building exterior. Interior work included evaporator coil installation integrated with existing Lennox furnace system in mechanical room, with PVC condensate drainage lines and refrigerant line connections completed. Performed electrical reconnection of all components, tested system operation, and verified proper refrigerant charge and airflow. Permits requested for mechanical, electrical, and air conditioning work per local code requirements. All equipment installed per manufacturer specifications with proper clearances maintained, system fully operational upon completion.

Provided comprehensive estimate for complete AC system replacement on 32-year-old R22 unit that experienced vibration issues causing unit displacement and subsequent failure. Original outdoor condenser installed in 1994 has reached end of serviceable life and uses obsolete R22 refrigerant, making repair economically unfeasible. Presented replacement options for modern high-efficiency system compatible with existing furnace infrastructure installed by our company previously.

Performed routine cooling maintenance on 32-year-old outdoor AC unit per customer's maintenance plan request. Conducted comprehensive diagnostic testing using digital multimeter to verify electrical readings and system performance, measured airflow at 305 CFM, and inspected all major components including compressor, capacitor, and condenser coil. All systems tested within acceptable parameters; unit operating properly with no cooling deficiencies identified.

Completed comprehensive Gold AC inspection on single-unit residential air conditioning system with basement-mounted air handler and outdoor condenser unit. System is under 10 years old and operating properly at time of inspection. Performed thorough evaluation of outdoor condenser unit positioned on concrete pad, including visual assessment of fan operation, protective grille condition, electrical connections, and proper airflow through mesh intake/exhaust panels. Verified electrical conduit connections and disconnect box mounting on exterior wall are secure and functioning correctly. Confirmed adequate clearance around condenser unit and documented equipment condition through photographic records for maintenance history.

Completed comprehensive Gold AC inspection on single Daikin condenser unit less than 10 years old. Per customer request, thoroughly cleaned condenser coils using water and compressed air to remove accumulated debris and ensure optimal heat transfer efficiency. Verified system operational status, inspected all accessible components including fan assembly and motor housing, and documented equipment condition with photographs showing unit positioned on proper pad with adequate clearance from fence line.

Conducted comprehensive site assessment for gas line installation serving outdoor mechanical equipment. Evaluated existing corroded piping infrastructure including blue-painted pump assembly with deteriorated flanges and oxidized connections, documented current system configuration with digital meter and pressure gauge components mounted on concrete pad adjacent to HVAC unit. Assessed backyard routing requirements from utility connection point through lawn area to equipment location, identified excavation pathway and measured distances for gas line extension to service mechanical systems at rear of residential structure.

Completed full HVAC system replacement including removal of 18-year-old furnace with cracked heat exchanger and non-functional air conditioning equipment. Installed new high-efficiency furnace with properly configured ductwork connections and new condensing unit. Replaced existing 40-gallon water heater with new unit, ensuring proper venting and code-compliant installation. All systems tested and operational upon completion.

Completed commercial HVAC maintenance agreement inspection on three AC units located upstairs. All systems were operational at time of service. Performed comprehensive inspection of Bryant Plus 90 high-efficiency furnace units, verifying proper operation of heating components, venting systems, and PVC condensate drainage lines. Inspected gas connections, electrical components, and safety controls on all three units. Documented equipment condition with photographs showing proper installation of white PVC venting systems with appropriate elbows and horizontal runs. All units passed inspection with no immediate service needs identified.

Completed comprehensive Gold AC inspection on single-unit Goodman HVAC system with air handler located in first-floor mudroom. Performed full system evaluation including condenser unit inspection, verified proper operation of all components, checked refrigerant lines and connections, inspected air handler cabinet and coil assembly, and documented equipment specifications and serial numbers. System confirmed operational with all components functioning within normal parameters; no service issues identified at time of inspection.

Performed furnace inspection and service in basement mechanical room. Accessed internal components by removing furnace panel to inspect blower motor assembly, wiring connections, and mechanical systems. Verified proper operation of unit and checked all electrical connections including multicolored wire bundles for secure termination and proper voltage.