Heating and Cooling Center Line

Provided comprehensive estimate for complete HVAC system replacement including furnace and air conditioning unit, plus chimney liner installation for basement-located equipment. Evaluated non-operational 25-year-old Amana natural gas furnace with attached Aprilaire humidifier, noting end-of-service-life condition requiring full replacement. Documented existing installation configuration, ductwork connections, and structural considerations for new equipment installation and proper venting requirements.

Responded to no hot water complaint and confirmed water heater failure in basement. Removed existing failed unit and installed new 40-gallon short tank-style water heater. Reconnected copper supply lines, drain valve, and temperature/pressure relief valve with discharge piping. Verified all connections for proper operation and tested unit functionality before completion.

Completed warranty return visit for new electrical install to address three thermostats requiring attention. Upon removal of existing thermostats from wall, discovered active cockroach infestation within the wall cavities and thermostat housings. Coordinated with pest control service to ensure proper treatment was completed prior to proceeding with thermostat installation. Installed and programmed three Rite Temp digital thermostats, verified proper wiring connections, and confirmed all units were functioning correctly with accurate temperature readings displayed.

Responded to service call for detached chimney vent cap damaged during recent storm. Performed exterior inspection of chimney system and assessed storm damage to cap assembly. Secured and reinstalled vent cap to manufacturer specifications, ensuring proper ventilation and weather protection. Verified adequate clearances and confirmed system integrity upon completion. Interior HVAC equipment and ductwork inspected and found to be in satisfactory operating condition with no related issues identified.

Completed comprehensive tune-up and inspection of residential furnace and air conditioning system located in basement. Performed multi-point inspection of heating unit including burner assembly, heat exchanger, blower motor, electrical connections, and venting system; verified proper ignition sequence and flame characteristics. Conducted AC system evaluation, checked refrigerant levels, inspected condenser coil, and tested overall system operation to ensure optimal performance for upcoming cooling season.

Completed Gold Furnace Inspection and tune-up on 3-year-old Lennox heating system in basement. Performed comprehensive cleaning and winter preparation service on furnace with no reported issues or symptoms. Inspected PureAir purification system and confirmed UV bulb replacement needed, with part already ordered from Lennox and scheduled for delivery to warehouse. Verified Lennox thermostat operation showing proper temperature control at 71°F current temperature with heating setpoint at 66°F. Inspected Bryant humidifier mounted on furnace and verified proper installation of white PVC vent piping. System operating within normal parameters and ready for heating season.

Completed full HVAC system installation including 45,000 BTU furnace, 2-ton air conditioning unit with rear discharge configuration, Honeywell Home programmable thermostat, and humidifier. Requested mechanical and electrical permits prior to installation. Reconnected existing electrical circuits and performed system remeasure for utility rebate qualification. Installed condensate pump and exterior condensate drainage line with PVC piping secured to building exterior. Mounted outdoor condenser unit on exterior wall with proper clearances. Programmed new digital thermostat and verified proper communication with equipment. All systems tested and operational upon completion.

Provided estimate for hot water boiler replacement in basement mechanical room. Existing system is very old with malfunctioning controls that prevent proper shutdown, presenting safety and efficiency concerns. Current installation includes aged copper piping with significant patina, multi-zone heating distribution system with floor-designated controls, expansion tank, and circulation pumps showing considerable wear from years of operation.

Completed full boiler installation with four-zone hydronic heating system, including installation of new boiler unit, four thermostats, four zone valves, and system controller. Established all electrical and mechanical connections, performed system startup and testing to verify proper operation of all zones. Mechanical and electrical permits secured prior to installation, with all required financing documentation completed and signed by loan holder before departure from property.

Completed early bird furnace inspection on two 10+ year old furnace units located in basement laundry room to assess equipment condition and evaluate potential storm damage concerns. Performed comprehensive system evaluation including visual inspection of both furnace units, ductwork connections, venting systems, and overall mechanical integrity to determine if replacement would be necessary in the near future.

Completed comprehensive furnace tune-up and inspection on 10+ year old unit located in basement laundry room. Performed thorough visual inspection of gas valve assembly (Model VRR205H 8016), verified all electrical connections including multi-colored wiring harnesses, and confirmed proper operation of 24V control system. Conducted internal ductwork inspection using borescope camera, documenting condition of flexible duct material and interior surfaces. All safety controls tested and operational, gas valve functioning properly with no leaks detected. System showed normal wear consistent with age, with no evidence of storm-related damage observed. Furnace remains serviceable with proper maintenance and no immediate replacement necessary at this time.

Completed comprehensive boiler repair work in basement utility area per approved estimate. Addressed copper piping connections, including vertical supply lines and horizontal elbow joints, with replacement of corroded sections showing significant rust staining on walls and floor. Repaired radiator heat exchanger system and associated mounting hardware, ensuring proper functionality of heating distribution components. All work completed with financing documentation processed and signed by loan holder, with identification verified and retained on file.

Completed comprehensive Gold level furnace inspection on an 11-year-old gas furnace located in the first floor laundry room. Performed thorough examination of all major components including heat exchanger, combustion assembly, gas valve, blower motor, electrical connections, and safety controls. All systems found to be operating within normal parameters with no immediate safety concerns or required repairs identified at this time.

Completed installation of new Lennox furnace system in basement utility area, including new thermostat and all associated ductwork connections. Permit was requested and financing approved prior to installation, with all work performed to manufacturer specifications and local code requirements.

Responded to service call for complete HVAC system failure following electrical repairs after storm-related power surge. Upon arrival, confirmed both heating and cooling systems inoperative with thermostat displaying OFF mode at 77°F. Evaluated 20-year-old furnace located in basement and 5-year-old central air conditioning unit. After diagnostic assessment of both systems and consideration of equipment age, power surge damage, and repair costs versus replacement value, provided comprehensive estimate for complete HVAC system replacement to restore heating and cooling functionality to residence.

Responded to no-cooling call on 20-year-old residential air conditioning system. Upon arrival, confirmed outdoor unit was not receiving power and indoor furnace was operational. Inspected electrical disconnect at outdoor unit and found deteriorated wiring connections with significant corrosion at terminal points. Cleaned terminals, replaced damaged wire connections, and verified proper voltage supply to contactor. Cycled system multiple times to confirm successful startup and normal operation of compressor and condenser fan.

Responded to no cooling call following electrical repairs after storm and power surge. Upon arrival, found both 5-year-old AC condenser unit and 20-year-old furnace inoperative with no power to either system. Performed electrical diagnostics using clamp meter at outdoor condenser unit and inspected contactor relay connections inside electrical panel. Identified tripped breakers and damaged contactor caused by power surge. Replaced failed contactor, verified proper wire connections on all terminals, reset breakers, and restored power to both HVAC systems. Tested AC unit operation with multimeter readings confirming proper voltage and amperage. System cycling normally with adequate airflow and cooling restored to residence.

Provided comprehensive estimate for complete boiler replacement of 66-year-old non-operational heating system showing extensive deterioration, including severely corroded control panel, aged mechanical components, and outdated piping configuration. Assessment included evaluation of existing gas valves, electrical controls, circulator pump, expansion tank, and associated plumbing infrastructure throughout basement utility area. Estimate encompasses removal of failed equipment and installation of new boiler system with updated controls and necessary piping modifications to restore residential heating functionality.

Completed comprehensive Gold AC and furnace inspection on 2024/2025 equipment with air handler located in basement. Performed thorough examination of outdoor condensing unit, verifying proper operation of compressor, condenser fan motor, and refrigerant levels. Inspected condenser coil fins for debris accumulation and airflow obstruction, noting unit positioned on stable platform with adequate clearance from landscaping. Checked electrical connections, contactor operation, and capacitor ratings on outdoor unit. Conducted detailed furnace inspection, examining burner assembly, heat exchanger, and gas delivery system components. Verified proper operation of ignition system and flame sensors. Inspected blower motor assembly and checked belt tension and condition where applicable. Examined all electrical connections including control board wiring and safety circuits. Verified proper function of LED diagnostic codes and status indicators. Checked condensate drainage system for proper opera

Responded to service call for basement pipe leak assessment following previous contractor's shutdown of basement access. Conducted thorough inspection of basement utility area, examining exposed copper gas lines, plumbing infrastructure, and mechanical systems throughout the space. Documented current condition of all visible piping, including vertical copper runs, valves, fittings, expansion tank, and pressure tank installations along cinder block walls. Inspected ceiling-mounted pipes running between floor joists, identifying copper and metal pipes requiring evaluation. Assessed basement accessibility and provided photographic documentation of existing plumbing system status to facilitate accurate estimate preparation for necessary repairs.