Efficient Heating and Cooling Services in Farmington Hills, MI

Completed annual cooling maintenance and AC tune-up on a 9-year-old Bryant system. Performed comprehensive inspection of outdoor condenser unit, verified proper system operation, checked refrigerant levels, cleaned components, and tested all safety controls. System found to be functioning properly with no deficiencies noted.

Performed comprehensive inspection on 4-year-old mini split system located behind garage. Conducted thorough evaluation of mini split unit, humidifier, thermostat, and hot water tank as requested. Identified heavily soiled air filters requiring immediate replacement due to significant dust and debris accumulation that could restrict airflow and reduce system efficiency.

Completed comprehensive Gold level seasonal maintenance on a 10-year-old residential boiler system in basement location. Performed full system tune-up including inspection of all major components, burner assembly, heat exchanger, and flue venting. Verified proper operation of combustion air intake and exhaust ventilation through galvanized vent piping. Inspected and tested expansion tank mounting and pressure settings. Examined all copper and brass supply and return piping connections for leaks or deterioration, noting insulation condition on hot water lines. Tested thermostat functionality and verified proper communication between control system and boiler unit. Checked gas connections, electrical components, and safety controls. Measured and documented operating pressures and temperatures to ensure system is performing within manufacturer specifications. Cleaned burner components and adjusted for optimal combustion efficiency. Verified proper condensate drainage and inspected all vis

Performed comprehensive tune-up on 2021 furnace located in basement utility room. Conducted full combustion analysis using calibrated diagnostic equipment, confirming natural gas system operating within manufacturer specifications with stack temperature at 391°F, CO2 at 7.1%, excess air at 58.4%, and carbon monoxide readings at safe levels. Inspected burner assembly, heat exchanger, blower motor, and ductwork connections; verified all components functioning properly with no safety concerns identified.

Responded to master bathroom plumbing issues involving stem leaks at stall shower and two vanity sink faucets, along with a leaking showerhead. Disassembled the three-piece chrome faucet assemblies on both undermount sink installations with granite countertops, replacing worn stem cartridges and seals to eliminate water seepage at the handles. Serviced the stall shower valve stems and replaced the showerhead to resolve dripping issue. Tested all fixtures under full water pressure to verify proper operation and confirmed no leaks at stems or spout connections upon completion.

Completed comprehensive whole home plumbing inspection for new homeowner. Inspected all accessible plumbing fixtures, supply lines, drain assemblies, and shut-off valves throughout the residence. Identified non-functional drain stopper mechanism in bathroom sink and noted excessive noise during bathtub water flow, likely caused by inadequate venting or drain line restrictions. Documented bathroom plumbing configuration including under-sink P-trap assembly with plastic tailpiece and PVC connections, braided stainless steel supply lines, and toilet water supply with brass angle stop valve. Observed evidence of previous water exposure on bathroom flooring near toilet shut-off valve area with visible staining on travertine tile surface, indicating potential historical leak or condensation issue. Photographed relevant plumbing components for documentation and customer reference. Provided detailed quote for necessary repairs including drain stopper replacement and investigation of bathtub dr

Completed comprehensive evaluation of 25-year-old furnace and humidifier system located in basement. Performed thorough inspection of HVAC equipment, humidifier, thermostat, and hot water tank as requested. Provided detailed replacement estimate for aging system, documented existing ductwork measurements and current equipment condition with photographic evidence for customer review.

Responded to service call for leaking kitchen faucet. Inspected brushed nickel pull-down faucet mounted on granite countertop with stainless steel undermount sink. Identified source of leak and performed necessary repairs to stop water dripping. Tested faucet operation to ensure proper function and confirmed no further leakage present.

Completed comprehensive tune-up and safety inspection on 25-year-old furnace system located in basement. Performed electrical diagnostics using digital multimeter to verify proper voltage and amperage readings across control board and system components. Inspection included evaluation of humidifier operation, thermostat functionality, hot water tank condition, blower assembly, wiring connections, and all safety controls to ensure system is operating within manufacturer specifications.

Responded to no cooling call on residential split system with 1-year-old outdoor condenser and 2-year-old attic air handler. Upon arrival, verified thermostat was calling for cooling with display showing 73°F setpoint. Inspected outdoor unit located in backyard on concrete pad and confirmed unit was not operating. Checked electrical connections at disconnect and verified 240V power supply present at condenser. Tested contactor and found failed contacts preventing compressor and condenser fan operation. Replaced defective contactor with OEM equivalent part. Cycled system through multiple cooling cycles to verify proper operation of compressor, condenser fan motor, and overall system performance. Confirmed adequate airflow at indoor registers and proper temperature split across evaporator coil. System restored to normal cooling operation with all components functioning as designed.

Completed comprehensive whole home plumbing inspection with emphasis on kitchen area in preparation for upcoming remodeling project. Inspected and documented sump pump system in basement, including PVC discharge piping, check valve configuration, and pump pit condition; noted operational status and water accumulation levels. Thoroughly examined under-sink plumbing infrastructure in kitchen area, evaluating PVC drainage system, supply line connections, and pipe joint integrity. Identified deteriorated wall conditions behind cabinetry with significant paint and plaster damage requiring attention during remodel. Documented all findings with photographic evidence for customer reference and contractor coordination.

Responded to service call for RTU blowing warm air on rooftop location. Accessed equipment using 24-foot ladder and performed diagnostic assessment of unit experiencing cooling malfunction. Completed filter replacement service on five total RTU units, installing new pleated air filters with proper dimensions (18x20x2 and 16x20x2) to restore airflow efficiency. Verified filter installation in air handler compartments and documented condition of HVAC systems post-service.

Completed comprehensive Gold AC inspection on 3-year-old air conditioning system with outdoor condenser unit located on exterior pad. Performed multi-point inspection including electrical connections, refrigerant levels, condensate drainage, airflow verification, and overall system performance testing. Unit found to be operating within normal parameters with no immediate service needs identified; confirmed proper installation on base pad with adequate clearance and verified all safety controls functioning correctly.

Performed comprehensive maintenance service on wall-mounted Rheem tankless water heater for new property owner. Conducted complete system flush to remove mineral buildup and sediment, inspected all plumbing connections including copper supply lines and brass fittings with isolation valves, verified proper operation of unit and all components, and confirmed system temperature output at 129°F. All components found to be in good working order with no leaks or operational issues detected.

Completed comprehensive inspection of single rooftop AC unit accessed via ladder. Performed visual assessment of RTU components, checked refrigerant lines, electrical connections, and mechanical systems per owner-required certification standards. Documented equipment condition with interior crawl space and exterior rooftop photographs showing unit location, surrounding infrastructure, and accessible service areas. All inspection criteria met and unit found operational within normal parameters.

Completed comprehensive Gold AC inspection on 12-year-old residential cooling system with outdoor condenser unit and basement-located air handler. Performed multi-point inspection including visual examination of condenser unit, verified proper airflow through ventilation fins, checked unit specifications and safety labels for compliance, and documented equipment condition through photographic records. System operational at time of inspection with condenser unit showing normal wear consistent with age, positioned in well-maintained backyard landscape with adequate clearance from surrounding vegetation for proper air circulation.

Responded to service call for central air conditioning system with no cooling capability. Upon inspection, evaluated existing HVAC equipment in mechanical room and exterior condenser unit at multi-unit building. Assessed system components including ductwork, venting, and outdoor condensing unit. Determined system required full replacement rather than repair. Provided estimate for complete HVAC system replacement including new air handler, condenser unit, refrigerant lines, and associated components necessary to restore cooling functionality to the property.

Completed comprehensive Gold Furnace Inspection on a one-year-old forced air heating system located in basement. Performed thorough examination of all mechanical and electrical components including gas valve assembly, ignition system, blower motor, and control board wiring connections. Inspected air filter condition and verified proper installation in filter compartment. All components found to be operating within normal parameters with secure wiring bundles and intact connections throughout system. Unit confirmed to be functioning properly with no deficiencies noted during inspection.

Completed comprehensive tune-up on 10+ year old residential air conditioning system with outdoor condenser unit and basement-located air handler. Performed standard maintenance protocol including inspection of condenser coils, cleaning of debris from protective mesh screen, verification of refrigerant levels, electrical component testing, and system operational check. Unit confirmed working properly with all components functioning within normal parameters.

Responded to no-cooling complaint on residential central air conditioning system. Upon arrival, found outdoor condenser unit with significant weathering and age-related deterioration. Inspected dual condenser setup with primary unit showing extensive rust and oxidation on copper-colored top grille, indicating prolonged exposure to elements. Evaluated electrical connections, refrigerant lines, and overall system operation. Documented equipment condition showing compromised components and aging infrastructure requiring attention to restore cooling capacity.