Heating and Cooling Hamtramck

Responded to no-heat call on steam gas boiler in basement. Upon inspection, diagnosed failed vent damper motor preventing boiler operation. Ordered replacement vent damper assembly for installation upon arrival at shop. Thermostat and batteries confirmed operational; issue isolated to defective damper actuator preventing proper venting sequence and boiler ignition.

Responded to callback for recently installed furnace and AC system not powering on. Inspected control board and wiring connections on furnace unit, photographed internal components including green circuit board with multiple wire connections and terminals. Determined Focus Pro thermostat required replacement from original installation and is currently at shop for exchange. Provided customer with Honeywell Home FocusPRO P200 Series thermostat user guide and quick reference documentation. System includes 70,000 BTU furnace, 2.5 ton AC unit, humidifier, APCO air purification system, and related components from initial installation requiring follow-up service to complete thermostat replacement and restore full system operation.

Completed installation of 2-ton air conditioning system with evaporator coil in rear basement location. Unit was properly mounted, connected to existing ductwork, and integrated with furnace system. All refrigerant lines, condensate drainage via PVC piping, and electrical conduit were installed per manufacturer specifications. System was tested for proper operation with thermostat controls. Mechanical and electrical permits were obtained prior to installation, with electrical reconnection coordinated through licensed electrician as required.

Completed comprehensive tune-up and inspection of residential furnace and air conditioning system located in basement. Performed diagnostic testing using digital meters to verify system pressures and electrical readings, checked refrigerant levels and gas valve operation, inspected ductwork connections and airflow throughout the system. All equipment found operating within normal parameters with no immediate repairs needed at this time.

Completed full HVAC system installation including a 70,000 BTU Lennox furnace, 2.5 ton air conditioning unit, humidifier, 40-gallon hot water heater with recirculation pump, and APCO air purification system. Installed new thermostat and verified all electrical connections, including meter reconnection. Ran white PVC exhaust and intake venting for high-efficiency furnace with proper termination. Obtained mechanical and electrical permits prior to installation. Verified system operation, tested all safety controls, and confirmed proper airflow throughout. Registered equipment with AHRI certificate number 215659728 for utility rebate eligibility.

Conducted furnace replacement estimate for 16-year-old heating system with failed heat exchanger located in basement. Evaluated existing electrical panel and service capacity to ensure compatibility with proposed equipment replacement, documented current electrical infrastructure including circuit breaker configuration and conduit routing for installation planning.

Completed Gold AC Inspection on a 16-year-old Bryant air conditioning system with air handler located in basement. Performed comprehensive maintenance inspection of outdoor condenser unit, which was found in good operating condition with no visible damage, rust, or deterioration to the cabinet or components. Verified proper condenser placement on concrete pad, confirmed adequate clearance around unit, and documented that surrounding area was clear of debris for optimal airflow and system performance.

Completed wall furnace installation and reconnection in residential space. Mechanical and electrical permits were requested and processed for the wall-mounted heating unit. Unit was installed below window in room with light green walls, with white ventilation grille properly mounted and appliance positioned for optimal heating distribution. All connections verified and system checked for proper operation upon completion.

Provided comprehensive estimate for complete HVAC system replacement in basement location. Existing 10+ year old air conditioning unit had failed inspection and required replacement. Evaluated current Bryant furnace system with natural gas fuel source, assessed existing ductwork configuration including sheet metal plenum with cross-bracing, and documented mechanical room layout with water heater and chimney infrastructure to ensure proper clearances and code compliance for new equipment installation.

Responded to service call for basement water drainage concerns. Upon inspection, found existing sump pump system with visible floor staining indicating previous water infiltration issues. Evaluated PVC discharge piping configuration running from basement floor to exterior discharge point. Verified pump operation and assessed drainage patterns on concrete floor surface. Confirmed system functionality and provided recommendations for ongoing moisture management in below-grade space.

Completed installation of 70,000 BTU furnace system including mechanical and electrical connections, liner installation, and reconnection of existing components. Obtained required mechanical and electrical permits prior to installation, and system qualified for utility rebate program. Exterior venting and electrical work completed with proper PVC pipe configuration and conduit installation visible on building exterior.

Completed on-site assessment of existing HVAC system and water heating equipment in basement mechanical room for replacement estimate. Documented current furnace unit with overhead ductwork configuration and two water heaters (one white/cream colored, one gray) installed against concrete block walls. Photographed equipment conditions, piping connections, electrical infrastructure, and spatial layout to provide accurate replacement specifications and equipment sizing recommendations.

Responded to homeowner complaint of intermittent banging noise from 2023 furnace located in basement. Performed diagnostic testing using Fieldpiece meter which revealed abnormal pressure readings (33.5/32.5) in the system. Inspected blower motor assembly and adjusted fan wheel to eliminate noise issue.

Successfully installed a new stainless steel pull-down kitchen faucet in a 20-year-old home. Replaced the existing fixture with a modern unit featuring integrated sprayer functionality. Verified proper water flow and confirmed no leaks upon completion of installation.

Performed inspection of 35+ year old non-functioning steam boiler with natural gas fuel source. Identified need for complete replacement of existing blue boiler unit showing significant wear and accumulation of dirt at base. Noted requirement for 4" venting installation with new boiler system to address current ventilation issues visible in concrete wall.

Responded to service call for furnace pilot failure on 4-5 year old basement unit. Inspected gas valve assembly and water level components, finding significant dust and debris accumulation affecting proper ignition. Cleaned affected components and restored pilot light functionality, ensuring proper system operation.

Diagnosed furnace cycling failure due to severely corroded heat exchanger with standing water present. Inspection revealed significant rust and oxidation on metal components, compromising system functionality and safety. Recommended complete replacement of heat exchanger or furnace unit as repair is not feasible due to extent of corrosion damage.

Performed Gold Furnace Inspection on 12-year-old forced air system located in basement. Verified proper burner ignition and flame pattern, inspected gas valve assembly and connections, and confirmed draft inducer motor operation. System functioning correctly with no issues identified.

Responded to service call for 4-5 year old furnace in basement with pilot light failure. Upon inspection, discovered significant corrosion on the pilot assembly components. Cleaned corrosion buildup, restored proper gas flow to pilot, verified ignition sequence, and confirmed normal system operation through complete heating cycle.

Performed inspection and evaluation of a non-functional 67-year-old wall-mounted gas space heater in the back bedroom. Unit is approximately 15-16 inches wide by 13-14 inches high, mounted on a mint green wall above wooden flooring. Measurements were taken and documentation photos captured to prepare replacement estimate for a new gas-powered wall heater with exterior venting capabilities.