Heating and Cooling Novi

Completed comprehensive Gold-level furnace inspection on residential forced-air heating system located in basement. Unit is less than 10 years old and operational at time of service. Performed thorough visual examination of burner assembly, confirming proper ignition sequence with uniform blue flame pattern across all five burner ports indicating optimal air-to-fuel mixture and complete combustion. Inspected internal components including electrical connections, wiring harness, motor assemblies, and mounting hardware—all found to be secure and in good working condition. Examined exterior condensing unit positioned on concrete pad against structure, verified fan operation and protective grille integrity, checked refrigerant line connections and condensate drainage system. Documented equipment condition with photographs showing active burner flames, internal component layout, and exterior unit installation. All systems functioning within normal operating parameters with no immediate safet

Responded to a plumbing leak originating from the kitchen sink and extending down to the laundry room area. Upon inspection, identified water damage to flooring and surrounding areas consistent with a progressive leak that had significantly worsened over recent days. Performed drain snaking service to clear blockage and address drainage issues contributing to the leak. Assessed plumbing connections and drainage system in the affected areas, documented conditions with photographic evidence showing workspace setup and equipment utilized during service. Completed necessary repairs to resolve the active leak and restore proper drainage function between the kitchen sink and laundry room in the residential property.

Responded to electrical code violation for air conditioning unit with improperly rated overcurrent protection. Replaced existing 30-amp fuses with correct 25-amp fuses per manufacturer specifications and local electrical code requirements, restoring the system to compliant operation.

Conducted site assessment for AC installation at commercial location with existing gas furnace and water heater in utility room. Evaluated space constraints and existing mechanical systems to determine appropriate equipment specifications. Customer requires new AC system installation with no existing cooling infrastructure present.

Successfully installed a 4-ton A/C unit and coil, completing all required refrigerant and electrical connections. Replaced aging components showing significant oxidation and corrosion, particularly on copper lines and metal surfaces. System now operational with all wiring properly connected to control board and blower assembly.

Diagnosed fluctuating water temperature issue on two commercial tankless water heaters. Inspected plumbing connections and drain assembly, identifying faulty flow sensor as the cause of temperature inconsistency. Replaced defective components and verified proper operation of both units, ensuring stable water temperature delivery to the three-compartment sink system.

Completed installation of a 40-gallon Icon System water heater in basement location. Unit features temperature control panel with safety settings and pilot light system. Installation included proper connection to existing plumbing infrastructure and verification of proper operation alongside Bryant furnace system.

Responded to callback regarding furnace continuous operation after maintenance. Inspected three units located in attic, all over 10 years old. Discovered and repaired damaged electrical connector on control board, which was causing the continuous run issue. All furnaces now cycling properly and operating within normal parameters.

Completed AC start-up service on outdoor condensing unit adjacent to brick structure. Unit was confirmed to be properly installed on concrete pad with adequate clearance for airflow. System was powered on, tested for normal operation, and all performance parameters verified within manufacturer specifications.

Performed Gold Furnace Inspection on a 16-year-old unit located in the basement. Examined interior components including control panel, safety systems, and electrical connections. Unit is currently operational with all warning indicators and safety features functioning properly.

Performed scheduled inspection on three commercial furnaces (age 10+ years). Accessed control compartments to inspect blower motors, circuit boards, and wiring connections. All units operating properly with no issues identified; connections and components appear intact with proper wire routing. Documented system condition with photos for service records.

Conducted on-site assessment of non-functional AC system requiring replacement. Evaluated existing Daikin HVAC installation, including furnace unit with PVC ventilation pipes, ductwork with metallic insulation, and associated components (condensate pump, air handler, filtration system). Provided customer with comprehensive replacement options based on current system specifications and home requirements.

Responded to callback regarding water leakage from humidifier connection. Removed existing saddle valve and installed new 1/4" humidifier shutoff valve to resolve the leak at the cold water line connection to the humidifier.

Successfully completed installation of a 135,000 BTU furnace with base, thermostat, and coil raising. Installed new metallic ductwork with proper sealing at all joints and connections, and performed all required electrical reconnections. System was fully tested with blower assembly and control board functioning properly, and all necessary mechanical and electrical permits were secured.