Local Heating and Cooling Services in Roseville, MI

Completed comprehensive tune-up and safety inspection on 10-year-old furnace unit located in basement. Performed full system evaluation including inspection of blower motor assembly, electrical connections, gas valve operation, and heat exchanger integrity. Checked and verified proper operation of thermostat, humidifier system, and associated hot water tank. All components found operating within normal parameters with typical dust accumulation for unit age. System tested and confirmed safe for continued operation.

Completed NSP AC inspection on outdoor condensing unit installed against brick exterior wall. Visual inspection confirmed unit in good operating condition with no visible damage, proper fan guard installation, secure mounting on base pad, and adequate clearance from structure. Documentation photos captured for service records.

Conducted site assessment for replacement estimate of 1.5-ton York Expedition air conditioning unit at residential property. Documented existing exterior electrical service configuration including dual meter setup, disconnect switch, and conduit routing on brick exterior wall. Inspected interior mechanical room containing current HVAC air handler, ductwork system, and associated utility equipment to determine compatibility requirements and installation parameters for proposed replacement unit.

Responded to service call for steam boiler with pilot light failure. Upon inspection, determined thermocouple was defective and heat exchanger exhibited cracking. Successfully relit pilot during diagnostic evaluation, but unit failed to maintain flame due to faulty thermocouple safety device. Given the age of the equipment (10+ years) and the compromised condition of the heat exchanger, provided estimate for boiler replacement as the heat exchanger damage presents a safety concern and repair is not cost-effective for equipment of this age.

Completed comprehensive Gold AC inspection on residential air conditioning system with air handler/coil located in basement. System is over 10 years old and currently operational. Performed thorough visual inspection of HVAC components, ductwork, and associated mechanical equipment. Documented equipment condition through photographic records showing air handler installation, ductwork insulation, and surrounding utility area. All system components verified to be functioning properly at time of inspection.

Responded to service call for 20-year-old Carrier furnace model 58MVB080-14 displaying 4-1-1 error code with complete system shutdown and no heating capability. Performed diagnostic evaluation and identified failed inducer motor as primary issue preventing unit operation. Due to age of equipment and high repair costs exceeding economical threshold, along with unconfirmed condition of heat exchanger, provided comprehensive replacement estimate for new furnace system. Documented existing unit configuration, photographed internal components and installation setup including ductwork connections and PVC venting system to facilitate accurate equipment sizing and replacement planning.

Completed comprehensive Gold AC inspection on 2023 air conditioning system. Performed visual assessment of outdoor condenser unit, confirmed proper installation on gravel pad, verified fan assembly and protective guard intact, and documented unit condition with photos showing clean, well-maintained equipment with no visible damage or deterioration. Renewed annual maintenance plan with homeowner on site.

Responded to a water leak in the basement of an older residential property. Upon inspection, identified a dripping valve on the existing copper piping system that had been actively leaking for approximately one week. Replaced the faulty valve with a new brass ball valve, tested the system for proper operation and verified no additional leaks were present in the surrounding plumbing infrastructure.

Performed comprehensive estimate inspection on 10+ year old HVAC system following identification of cracked heat exchanger in American Standard furnace unit located in basement mechanical room. Evaluated existing R410A air conditioning system and assessed feasibility of complete system replacement including furnace and AC unit. Documented current equipment configuration, ductwork connections, venting setup with white PVC exhaust/intake pipes, and overall system condition to provide homeowner with replacement options for full HVAC system upgrade.

# HVAC Gold AC Inspection Completed Performed comprehensive Gold-level air conditioning inspection on a single 10+ year old residential system with air handler located in basement. System was operational at time of service. Conducted thorough examination of refrigerant lines and electrical connections at indoor unit, noting foam insulation on copper refrigerant piping with age-appropriate wear. Verified proper routing of control wiring including multi-conductor thermostat and power supply connections through equipment cabinet. Inspected outdoor condensing unit and discovered severe deterioration of electrical components. Found extensively corroded capacitor housing with heavy rust buildup on internal metal components and mounting hardware. Noted significant debris accumulation including cobwebs throughout electrical compartment indicating prolonged lack of maintenance. Documented corroded conduit connections and weathered wiring at outdoor unit base. Equipment shows advanced signs

Conducted comprehensive site assessment for complete HVAC system replacement in residential basement installation. Evaluated existing air handler unit with galvanized metal exterior and associated ductwork configuration for replacement and relocation to alternative position within the space. Assessed current furnace system and provided technical specifications for complete heating system replacement, documenting existing equipment conditions, ductwork routing, and spatial requirements for proposed system modifications.

Responded to service call for 10-month-old AC unit in basement with no heating or cooling capability, though blower motor was operational. Performed diagnostic evaluation and identified malfunctioning control board as root cause of system failure. Accessed control board assembly housed in black plastic enclosure, inspecting circuit boards, wiring connections, and terminal blocks. Verified thermostat communication and settings showing 72-degree setpoint on Emerson unit. Replaced defective mitigation board, ensuring all wire connections were properly secured to terminal blocks and system controls were functioning correctly. Tested system operation to confirm restoration of heating and cooling functions.

Installed new gas line from existing supply to outdoor grill location on residential property. Routed black iron pipe along exterior foundation, ensuring proper support and code-compliant installation. Pressure tested system and verified all connections for safe operation.

Completed warranty installation of a 40-gallon Bradford White standard tank water heater in residential basement utility area. Reconnected all water supply lines including copper piping and galvanized connections with proper elbow joints, installed pressure relief valve assembly, and connected gas control unit at base of tank. All plumbing connections tested and verified operational with no leaks detected.

Completed air conditioning system start-up for basement evaporator coil installation. Performed electrical measurements using digital clamp meter, verifying proper amperage draw readings of 26.0A and 24.24A on the system, confirming equipment is operating within manufacturer specifications and safe operating parameters.

Completed plumbing estimate for installation of new gas line routing from basement utility area to exterior patio location. Assessment included evaluation of existing basement piping infrastructure, identification of optimal routing path through floor joists and foundation penetration point, and determination of required materials including black iron pipe, fittings, shutoff valves, and exterior termination components. Exterior patio area and screened porch structure were inspected to establish final connection point for outdoor gas appliance hookup.

Completed full HVAC system installation including a 70,000 BTU furnace and 2-ton air conditioning unit with rear discharge configuration. Installed humidifier, condensate pump, and all necessary ductwork connections. Requested mechanical and electrical permits prior to installation. Performed complete system startup, refrigerant charging, and vacuum testing using manifold gauges to verify proper pressurization and system integrity. Reconnected all electrical and gas connections per manufacturer specifications. System tested and operational, meeting all code requirements. Documentation submitted for utility rebates through Consumers Energy and DTE Energy programs. AHRI certificate number recorded for rebate processing.

Provided estimate for complete air conditioning system replacement. Existing 2007 system was non-functional with complete R22 refrigerant loss as previously diagnosed by another contractor. Assessed outdoor condensing unit located against brick exterior and basement furnace installation to determine replacement specifications and compatibility requirements for new equipment.

Completed comprehensive Gold AC inspection on multi-unit residential HVAC system with 11-year-old equipment. Inspected outdoor condenser unit positioned on exterior wall with proper clearance from debris, verified fan operation and examined electrical connections. Serviced basement-located air handler, inspected and evaluated pleated air filter condition within the unit, and assessed blower motor assembly and associated mechanical components. All systems operating within normal parameters at time of inspection.

Completed sold repair on electrical equipment mounted to ceiling structure, requiring approximately 4 hours of labor. Serviced device with light blue housing secured to white ceiling surface, with associated black corrugated conduit for wire management running horizontally below the unit. Documented installation with photographs showing proper mounting hardware and conduit routing in interior utility space.