Heating and Cooling Ecorse

Completed full HVAC system installation including new Lennox furnace unit and 40-gallon water heater in basement utility area. Installed new Honeywell programmable thermostat with digital display and connected to heating system. Configured ductwork connections and integrated condensate pump into system. Coordinated utility rebate application and obtained necessary permits for installation. All equipment tested and operational upon completion.

Responded to service call for 20-year-old Lennox G26Q3-50 forced air furnace in basement experiencing inadequate heating issues. Conducted comprehensive system evaluation and provided detailed estimate for complete HVAC system replacement, including assessment of existing ductwork, electrical connections, and venting infrastructure to ensure proper sizing and compatibility for new equipment installation.

Responded to no heat concern on 20-year-old Lennox G26Q3-50 forced air furnace in basement. Performed comprehensive system inspection and diagnostic testing using clamp meter to verify electrical readings and borescope camera to inspect heat exchanger. Internal inspection revealed extensive rust and corrosion throughout heat exchanger with significant deterioration visible on interior surfaces. Advised customer that heat exchanger failure presents safety hazard due to potential carbon monoxide leakage and unit has reached end of serviceable life. Recommended immediate replacement of furnace given age of equipment and severity of corrosion found. Provided replacement options and discussed system sizing requirements for home.

Completed Gold Boiler Inspection on a National Gas steam boiler, over 10 years old, located in basement. Unit is operational and functioning properly at time of inspection. Performed comprehensive visual assessment of boiler components, verified proper operation, and documented equipment condition with photographs for maintenance records.

Responded to no cooling complaint on three-year-old residential air conditioning system with attic-mounted air handler and ground-level condenser unit. Upon arrival, accessed attic equipment via ladder and performed diagnostic evaluation of both indoor and outdoor components. Inspected condenser unit, confirmed fan operation and verified equipment condition, documenting findings with photographs for service records.

Responded to service call for continuously running toilet. Upon inspection, found deteriorated flush valve flapper and compromised fill valve components causing constant water flow. Toilet tank interior showed significant mineral buildup and hard water staining indicating prolonged operational issues. Assessed internal tank mechanisms including flush valve assembly, fill valve, and associated rubber components for wear and functionality. Documented existing conditions showing discolored flapper seal and aged internal hardware requiring replacement to restore proper operation and prevent water waste.

Completed furnace inspection on Trane heating unit located in basement utility area. Assessed overall system condition, ductwork connections, and operational components to provide replacement estimate. Documented existing equipment configuration including air handler, ventilation system, and associated mechanical components for homeowner's consideration of system replacement options.

Completed comprehensive furnace inspection and tune-up on gas furnace unit located in basement. Performed visual inspection of burner assembly, heat exchanger, and internal components using borescope camera to assess condition of hard-to-reach areas including ductwork insulation and air handling compartments. All components found to be in serviceable condition with no immediate safety concerns identified.

Conducted on-site assessment for new whole home generator installation at residential property. Documented generator placement specifications with unit to be installed at rear of home in parallel orientation, maintaining 8-foot clearance from side lot line in compliance with manufacturer requirements. Evaluated existing electrical panel, meter grade to drop measurements, and verified gas meter location and routing path from gas service to proposed generator location. Confirmed clearance requirements for air intake, exhaust positioning, and distances from windows and openings per installation standards.

Completed installation of 45,000 BTU residential furnace in utility room with all necessary mechanical and electrical connections. Installed new PVC venting system routed through exterior wall, connected gas line, and performed electrical reconnection work. Applied for mechanical and electrical permits, completed remeasurement for utility rebate qualification, and verified all equipment is operating to manufacturer specifications.

Performed furnace inspection on 16-year-old heating system located in basement of vacant residential property. During diagnostic evaluation, discovered cracked heat exchanger, rendering unit unsafe for operation and beyond economical repair. Provided estimate for complete furnace replacement due to critical safety hazard that cannot be remediated through standard repair procedures.

Completed furnace inspection and tune-up for rental certification on a 16-year-old unit located in the basement of a vacant property. System was found operating properly with no reported issues or deficiencies noted during the comprehensive inspection. All components tested within normal parameters and unit approved for certification.

Conducted on-site assessment of existing HVAC equipment for replacement estimate at residential property. Evaluated exterior-mounted utility connections, electrical meter infrastructure, and current system configuration including fuel type determination and equipment accessibility along building exterior. Documented existing conditions with photographic evidence showing weathered meter equipment, drainage systems, and outdoor unit placement area adjacent to brick structure for proper sizing and installation planning of replacement system.

Completed full HVAC system installation including a 70,000 BTU furnace and 2-ton air conditioning unit in basement utility closet with rear yard condenser placement. Installed new thermostat, condensate pump, and established all electrical connections at breaker panel with dedicated circuits for furnace and AC unit. Secured all required mechanical and electrical permits, reconnected existing ductwork, and remeasured return air for proper system airflow and efficiency.

Conducted comprehensive inspection of 10-year-old furnace system located in basement following reports of operational concerns. Upon examination, identified cracked heat exchanger requiring immediate shutdown for safety reasons. Evaluated existing R22 refrigerant air conditioning system and outdoor condensing unit positioned on concrete pad in backyard area. Provided full system estimate for complete HVAC replacement due to failed heat exchanger and obsolete R22 refrigerant technology, documenting equipment condition through photographic records of outdoor condensing unit installation, electrical connections, and refrigerant line routing.

Completed comprehensive tune-up and inspection on 10-year-old furnace system located in basement. During inspection, identified significant crack in supply plenum ductwork that requires immediate attention to prevent air loss and efficiency degradation. Documented aged and deteriorated insulation on main trunk line ductwork in attic space showing visible dirt accumulation and wear at connection points. Performed standard maintenance procedures including filter inspection, burner assembly cleaning, heat exchanger examination, blower motor lubrication, thermostat calibration, and combustion analysis to ensure safe and efficient operation. System is currently operational but recommend scheduling ductwork repairs to address the cracked plenum and consider re-insulating trunk line to restore proper thermal efficiency and airflow distribution throughout the home.

Responded to gas pressure concerns affecting entire residence in 70-year-old home. Performed comprehensive pressure test on gas line and meter assembly located in basement to identify potential leaks or pressure irregularities that had been present for approximately one week. Conducted thorough inspection of gas piping system throughout basement area, examining exposed black iron pipe runs, joints, and connections along ceiling joists and support beams. Utilized pressure testing equipment to pressurize gas lines and monitor for pressure drops indicating leaks. Testing apparatus was set up at exterior gas meter location to isolate and test the complete system from meter through interior distribution lines. Applied industry-standard pressure testing protocols, monitoring gauge readings over extended period to ensure system integrity. Inspected all visible pipe hangers, support clips, and connection points for proper installation and signs of deterioration consistent with age of home. D

Performed routine maintenance and inspection on a five-year-old main floor furnace unit with no reported operational issues. Conducted comprehensive tune-up including visual inspection of blower motor assembly, electrical connections, and wiring harnesses, verifying all components were properly secured and functioning within normal parameters. All systems tested and confirmed operational with no deficiencies noted.

Completed comprehensive Gold AC inspection on residential cooling system with equipment age over 10 years. Performed full system evaluation including outdoor condenser unit and attic-located air handler, verifying operational status, measuring system performance parameters, and inspecting all major components. Advised customer to maintain clear area around condenser unit free of debris for optimal airflow and system efficiency.

Conducted on-site assessment for air conditioning unit installation at residential property. Evaluated existing HVAC ductwork configuration in attic/crawlspace area, including rectangular metal supply ducts, air handler components, and flexible duct connections with foil-faced insulation. Inspected exterior electrical service panel and conduit routing on building exterior to verify electrical capacity and determine optimal placement for new AC condenser unit. Documented current system layout and utility connections through photographic documentation. Provided comprehensive equipment replacement estimate including recommended unit sizing, installation requirements, and necessary modifications to existing ductwork and electrical infrastructure to accommodate new air conditioning system.