Heating and Cooling Franklin

Replaced existing low-profile toilet with a comfort-height toilet unit to accommodate accessibility requirements. Removed old toilet by disconnecting water supply line, unbolting floor flange connections, and properly disposing of existing fixture. Installed new ADA-compliant comfort-height toilet, ensuring proper wax ring seal at floor flange, securing mounting bolts to manufacturer specifications, and reconnecting water supply line. Tested flush mechanism, tank fill valve operation, and verified no leaks at supply connection or base seal upon completion.

Completed comprehensive Gold Plan furnace inspection on 12-year-old basement heating unit. Performed full system tune-up including inspection of heat exchanger, burner assembly, ignition system, blower motor, and all safety controls. Inspected and documented humidification system with water panel evaporator pad, verified proper drainage through condensate trap and PVC drain line assembly, and confirmed electrical connections secure. All components found operating within manufacturer specifications with no immediate service needs identified.

Completed annual Gold Plan boiler inspection and tune-up on 10-year-old heating system in preparation for the upcoming cold weather season. Performed comprehensive maintenance including inspection of pressure reducing valve, flow control components, and associated copper piping connections with insulation. System confirmed operational and ready for winter heating demands.

Responded to no heat call for 14-year-old furnace located in basement of commercial facility. Upon arrival, confirmed unit was not operating and conducted diagnostic inspection of heating system and associated components. Documented existing gas line configuration and utility connections with visible corrosion on exterior piping and fittings, noting weathered valve assembly and threaded connections requiring attention for safe operation.

Performed comprehensive tune-up and inspection on 2-year-old hot water boiler system located in lower level mechanical room. Inspection included thorough evaluation of boiler operation, water heater functionality, humidifier system, and thermostat controls. All equipment found operating within normal parameters with proper connections and venting confirmed.

Responded to generator service call following extended storm operation. Unit had been running continuously for four days and required manual start activation. Performed comprehensive maintenance inspection on standby generator system. Removed access panels to examine internal components including Vanguard engine assembly, air filtration system, electrical connections, and control wiring. Inspected rubber-mounted grommets and isolation bushings for wear and proper seating. Verified all electrical connections were secure with no signs of overheating or corrosion from extended run time. Examined air filter condition and engine compartment for debris accumulation. Confirmed unit operational status and proper shutdown procedures. Key left in generator control panel as requested for customer access.

Completed annual Gold AC inspection and tune-up on residential HVAC system. Performed comprehensive maintenance including visual inspection of furnace interior components, verified proper operation of gas valve assembly, blower motor, and blower wheel, checked all electrical connections and wiring, and confirmed main floor thermostat functionality. All components found in good working condition with no issues identified or additional repairs required.

Installed complete second floor laundry plumbing system including supply lines, drainage piping, two waste stacks, and floor drain. Permit was obtained and all work performed to code specifications. System tested and operational upon completion.

Responded to service call for zoned HVAC system experiencing issues. Ordered replacement zone damper motor for third floor zone, which will be installed upon arrival at shop. Documented significant frost accumulation on ductwork components and condensation on access panels, indicating potential airflow restriction or refrigerant issues related to failing damper motor. Scheduled return visit to replace malfunctioning Aprilaire zone damper motor on third floor and install new Sensi thermostat on main floor to restore proper zone control and system operation.

Completed installation of 2-ton air conditioning system with matching evaporator coil in right-side configuration. Performed system flush and reconnected electrical components per code requirements. Successfully installed new ductwork with multiple 90-degree transitions, secured refrigerant lines, routed condensate drainage with white PVC piping, and integrated all components with existing furnace/air handler unit. Applied proper labeling to ductwork sections and verified all mechanical and electrical connections. System remeasured and tested for proper operation upon completion.

Responded to no-cool complaint on one of four AC units at property with 11-year-old equipment. Performed diagnostic evaluation on non-operational unit located in office area of residence, identifying cooling system failure. Conducted courtesy inspections on three additional functioning AC units as requested, including attic-mounted system accessed with extension ladder. All outdoor condensing units showed normal operational condition with clean cabinets, functional fan assemblies, and proper airflow through condenser coils. Documented equipment conditions with photographic records showing well-maintained exterior components and appropriate installations against building exterior.

Responded to water leak complaint on 10+ year old hot water boiler located in basement mechanical room. Upon inspection, identified active leak originating from boiler system piping connections. Examined expansion tank assembly, associated copper piping network, pressure relief components, and circulation system connections. Tightened compromised fittings, inspected pressure gauges and zone valves, and verified all connections throughout the hydronic heating system for proper seal integrity. System tested and confirmed operational with no further leakage detected at time of service completion.

Evaluated four residential AC units at property, with primary focus on one non-operational system approximately 11 years old located in office area. Inspected outdoor condenser unit and attic-mounted air handler, identifying low refrigerant charge in studio unit. Assessed electrical disconnects, ductwork configuration, and overall system condition across all four units. Provided comprehensive replacement estimate for aging equipment showing signs of refrigerant loss and wear.

Conducted on-site plumbing estimate for piping repairs in residential property. Assessed unfinished construction area with exposed drywall and identified plumbing access point through wall cutout requiring pipe repair or replacement. Evaluated kitchen area with modern cabinetry to determine scope of work for concealed piping systems behind walls and beneath fixtures. Documented conditions with photographs for detailed estimate preparation and provided recommendations for necessary piping repairs to restore proper function.

Responded to service call for washer and dryer installation plumbing assessment. Upon arrival, conducted thorough inspection of the property to locate existing water supply lines and drainage connections required for laundry appliance installation. Inspected exterior hose bib on building perimeter and traced copper supply lines through attic space to identify accessible water source points. Located main water supply piping with shutoff valve in attic area above proposed appliance location. Documented existing plumbing infrastructure through photographic evidence showing exterior water connection point and accessible copper piping with valve assembly in ceiling/attic space. Provided homeowner with assessment findings regarding available plumbing connections and routing options for washer supply lines and drain installation.

Completed Gold AC Inspection on a 3-year-old Daikin outdoor condenser unit. System was operational at time of inspection, with all components functioning properly and no visible exterior damage or wear noted. Verified unit condition, checked electrical disconnect, and confirmed proper installation with adequate clearance and drainage on concrete pad.

# Plumbing Service Completed Responded to service call for corroded copper refrigerant lines on exterior HVAC system. Upon inspection, identified significant copper oxidation and verdigris formation at multiple soldered joints and along exposed pipe surfaces, indicating prolonged moisture exposure. Replaced deteriorated copper line set with new refrigerant-grade copper piping, ensuring proper brazing techniques and leak-free connections. Additionally addressed plumbing issue in attic space where copper water supply line showed signs of leakage contributing to moisture damage on surrounding wooden joists and subflooring. Installed new brass shutoff valve on copper supply line and secured proper foam insulation to prevent future condensation issues. Verified no active leaks present after installation and confirmed adequate ventilation in attic space to minimize future moisture accumulation and mold growth on structural components.

Responded to a whole-house low water pressure issue that had persisted for three days. Upon inspection, diagnosed a failing pressure tank system in the crawl space. The existing turquoise Well-Rite pressure tank showed signs of waterlogging and loss of air charge, preventing proper pressure regulation throughout the home. Inspected the associated plumbing assembly, including the main shutoff valve with black wheel handle, pressure switch, and connecting piping. Found corroded fittings and compromised connections contributing to system inefficiency. Tested pressure readings at the tank and verified inadequate pressure maintenance. Explained findings to homeowner, including the need for pressure tank replacement and potential valve assembly updates to restore proper water pressure throughout the residence. Documented existing conditions with photographs for reference and provided recommendations for complete system restoration.

Responded to water leak reported in hallway area. Upon inspection, identified active water intrusion causing significant ceiling damage with brownish staining, discoloration patterns, and compromised drywall with visible breakthrough to substrate. Inspected bathroom plumbing fixtures including toilet and supply lines to isolate leak source. Assessed shut-off valve functionality and checked for visible signs of pipe deterioration or fixture failure. Documented extensive water damage patterns indicating ongoing moisture intrusion requiring further investigation to determine if leak originates from supply lines, drain pipes, or second-floor plumbing above damaged ceiling area. Recommended comprehensive plumbing system evaluation to determine extent of repairs needed versus full system replacement.

Responded to warranty call for newly installed furnace with non-operational third-floor zone in existing three-zone HVAC system. Performed diagnostic testing on zoning system and verified furnace operation along with proper function of two remaining zones. Installed new Sensi digital thermostat, programmed heating settings, and confirmed system communication with zoning board.