Heating and Cooling Dearborn Heights

Responded to service call for thermostat malfunction and low airflow from supply registers. Diagnosed and resolved thermostat issue, restoring proper system operation. Assessed vent airflow concerns and provided recommendations for duct cleaning services to improve system efficiency.

Completed comprehensive NSP furnace inspection on basement-installed Daikin unit. Accessed internal components by removing front panel, performed visual assessment of blower motor assembly, heat exchanger, electrical connections, and control wiring. Utilized diagnostic testing equipment to verify system operation and component functionality, with all major components found to be in working order at time of inspection.

Completed prepaid maintenance visit on 14-year-old furnace located in basement. Inspected condensation pump as requested by customer and verified proper operation. Replaced 16x25 air filter per scheduled maintenance protocol. Performed standard maintenance inspection of furnace components including blower assembly, electrical connections, and control board, with all systems found operating within normal parameters.

Responded to emergency call for carbon monoxide leak originating from stove gas line. Conducted thorough inspection of gas line connections and fittings throughout the system, including exposed piping in basement area. Identified compromised connection at stove supply line, tightened fittings, and performed pressure test to verify leak was sealed. Conducted carbon monoxide testing to confirm safe levels restored throughout the home and verified all gas appliances were functioning properly with no further leaks detected.

Installed outdoor GFCI receptacle in weatherproof Intermatic enclosure on exterior siding. Wired dual outlet with integrated toggle switches and indicator light, then connected circuit to dedicated breaker in main electrical panel labeled "Outdoor GFCI." Verified proper ground fault protection and tested functionality of all outlets and switches to ensure code-compliant operation.

Completed comprehensive Gold-level maintenance inspection on residential HVAC system including 1-year-old furnace located in basement and 8-year-old outdoor condensing unit. Performed thorough examination of furnace interior components including blower motor assembly, electrical connections, control module, and wiring harnesses; verified all connections secure and components operating within normal parameters. Inspected outdoor air conditioning condenser unit positioned on concrete pad against exterior brick wall; evaluated cabinet condition, coil cleanliness, and overall system operation. Both units found to be in good working condition with no immediate service needs identified during this preventative maintenance visit.

Completed full HVAC system installation including a 70,000 BTU furnace and 2.5-ton air conditioning unit with rear discharge configuration. Installed new thermostat, reconnected electrical components, and performed system flush on condensate pump. Verified proper operation of all equipment, confirmed AHRI certification matching, and documented installation for utility rebate qualification.

Conducted on-site evaluation for residential air conditioning system replacement. Assessed existing outdoor condensing unit located on rear deck area with electrical service and conduit installation. Documented current Honeywell digital thermostat displaying operational status and humidity readings. Based on property size and cooling requirements, determined appropriate replacement unit sizing in the 2 to 2.5 ton capacity range. Photographed equipment location, electrical connections, and existing HVAC controls for replacement planning and proposal development.

Conducted comprehensive site assessment for whole home generator installation at residential brick structure. Evaluated existing electrical infrastructure including dual meter configuration, conduit routing, and junction box placement on exterior wall to determine optimal integration point for generator system. Documented current electrical service capacity and identified suitable location for generator placement considering clearance requirements, fuel line access, and proximity to existing electrical panels for efficient transfer switch installation.

Completed electrical estimate for new whole home generator installation at manufactured home. Assessed existing electrical panel configuration, circuit breaker capacity, and available utility space in basement area to determine optimal generator placement and integration requirements. Documented current electrical infrastructure including panel layout, available circuits serving kitchen, dining room, and range, along with basement utility area conditions to develop comprehensive installation plan and equipment specifications.

Completed electrical estimate for new whole home generator installation at residential property. Assessed existing electrical service panel, meter location, and available space in rear yard for generator placement. Evaluated property layout including setback requirements, utility access points, and optimal positioning for equipment installation while maintaining compliance with municipal regulations.

Provided comprehensive estimate for Kohler residential standby generator installation at exterior brick wall location. Evaluated existing electrical infrastructure including conduit routing, utility box placement, and determined optimal pad placement on lawn area adjacent to building. Assessed natural gas fuel source availability and confirmed adequate clearances from windows, HVAC equipment, and property lines for code-compliant generator positioning.

Responded to no cooling complaint on 3-year-old air conditioning system following power outage restoration. Upon arrival, performed diagnostic evaluation of outdoor condensing unit and indoor evaporator coil connected to basement furnace. Inspected electrical connections, control board, and wiring harness for damage related to power surge or outage event. Checked air filter condition and found heavily soiled filter restricting airflow. Verified thermostat communication, contactor operation, and system startup sequence. Restored unit to proper operation and confirmed cooling cycle engaged successfully.

Installed two modern circular LED ceiling light fixtures in residential interior spaces. First fixture was mounted in main living area ceiling above music room, and second fixture was installed in hallway ceiling between bedroom access points. Both fixtures feature chrome-rimmed design with integrated LED panels, properly wired to existing electrical circuits, tested for functionality, and confirmed operational upon completion.

Responded to service call for malfunctioning toilet handle in main floor bathroom. Upon inspection, found toilet flush handle mechanism sticking in downward position, preventing proper return to neutral position after flushing. Disassembled flush handle assembly and identified worn internal components causing binding. Replaced defective flush handle mechanism with new assembly, ensuring proper spring tension and smooth operation. Tested flush cycle multiple times to verify handle returns to correct position without sticking. Unit now operates normally with full flush functionality restored.

Successfully completed installation of 2.5-ton air conditioning system with evaporator coil in rear yard location. Installed new Lennox furnace with A-coil in interior utility space, including proper condensate drain lines using PVC piping, flexible ductwork connections, and all required venting. Exterior condenser unit positioned on concrete pad in backyard with refrigerant lines reconnected and system charged to manufacturer specifications. All mechanical components installed per code requirements with permit requested for inspection.

Responded to urgent service call for non-operational furnace system affecting whole-house heating and cooling capabilities. Assessed 35-year-old original equipment installed in 1991, located in basement mechanical room. Documented existing furnace installation including cabinet unit, ductwork connections, filter housing, and associated copper and brass piping components. Provided comprehensive replacement estimate for complete HVAC system replacement due to equipment age and failure affecting both heating and air conditioning functionality.

Completed routine preventative maintenance tune-up on a four-year-old residential air conditioning system located in the backyard. Performed comprehensive inspection of the outdoor condenser unit, including examination of the fan assembly, motor, and protective wire guard. Verified proper operation of the top-mounted fan, checked all electrical connections and conduit, and inspected refrigerant lines for signs of wear or damage. All components found to be in good working condition with no issues identified during the service visit.

Completed comprehensive HVAC system evaluation for 26-year-old R22 heating and cooling system located in basement. Identified low refrigerant charge in air conditioning unit and assessed overall condition of aging Lennox furnace with AprilAire humidifier component. Provided replacement estimate for complete system upgrade due to obsolete R22 refrigerant and equipment age exceeding typical service life.

Completed comprehensive Gold AC inspection on 26-year-old outdoor condensing unit. Performed electrical diagnostics using clamp meter to verify amperage draw and system performance. Inspected condenser coils through mesh grille, noting unit's age and weathered exterior condition. Evaluated fan assembly operation and overall system functionality. Unit currently operational with air handler/coil located in basement. Documented equipment condition with photographic evidence showing outdoor condenser positioned on concrete pad with surrounding vegetation growth and minor debris accumulation at base.