Heating and Cooling Huntington Woods

Responded to service call for non-operational Bryant humidifier system located in basement. Upon inspection, diagnosed failed water supply motor preventing proper water distribution to humidifier pad. Motor showed no electrical continuity and was unable to pump water through supply line to humidification assembly. Replaced defective water supply motor with OEM equivalent component, reconnected water supply tubing and electrical connections, and verified proper operation of humidifier system integrated with existing HVAC ductwork.

Completed comprehensive Gold AC Inspection and tune-up service on two 14-year-old air conditioning systems—one basement unit and one upstairs unit. Performed thorough system evaluation on both indoor air handlers and outdoor condensers, including inspection of blower motor assemblies, fan components, electrical connections, and refrigerant lines. Removed access panels to examine internal components, verified proper operation of all mechanical systems, and checked condensate drainage. Inspected outdoor condenser units positioned on brick patio area, evaluating fan grilles, protective mesh housing, refrigerant line connections, and electrical conduit routing. Both systems demonstrated normal operational parameters for units of this age and received preventive maintenance to ensure continued reliable performance throughout the cooling season.

Responded to a commercial property for a garbage disposal experiencing intermittent leaking and operational issues. Upon inspection, examined the 1/2 HP disposal unit mounted under the kitchen sink, including all connection points, drain lines, and electrical components. Verified power supply and confirmed circuit breaker was in the on position, then assessed the disposal's mounting flange, discharge plumbing, and dishwasher drain connection for signs of leakage or loose fittings.

Completed Gold AC Inspection on a 6-year-old single-unit air conditioning system with air handler located in basement. Performed comprehensive maintenance inspection of outdoor condenser unit and verified system operational status, with all components functioning properly at time of service.

# Plumbing Repair Completed Responded to service call for under-sink plumbing concerns. Upon inspection, discovered significant condensation accumulation on galvanized supply pipes beneath bathroom fixture, indicating potential temperature differential issues or inadequate ventilation. Photographically documented existing pipe assembly configuration, including chrome shut-off valve connections and mounting hardware. Assessed attic space above service area to identify any contributing factors, noting exposed framing, fiberglass insulation placement, and utility routing. Verified all threaded connections were secure and properly sealed. Ensured proper drainage function and confirmed no active leaks present in the supply line assembly.

Completed comprehensive Gold AC inspection on 7-year-old residential cooling system with air handler located in basement. Performed multi-point inspection of outdoor condensing unit including visual assessment of fan assembly, grille condition, and mounting hardware. Verified proper clearance around condenser unit with debris-free perimeter, confirmed operational status of system components, and documented equipment condition through photographic records showing normal wear patterns consistent with unit age.

Responded to service call for multiple plumbing concerns throughout the residence. Replaced external valve and associated outside piping to restore proper water flow and eliminate leakage. Addressed small bathroom sink equipped with four individual valves, performing necessary replacements to ensure proper operation and shutoff capability. Disassembled and rebuilt shower mixer valve assembly, replacing worn internal components including cartridge, seals, and O-rings to restore proper temperature control and eliminate cross-flow issues. Investigated kitchen sink drainage problem with reduced flow rate. Upon inspection, identified corroded P-trap assembly with significant mineral buildup and verdigris formation on metal components. Removed deteriorated metal trap sections and replaced with new PVC drain assembly to improve drainage performance and prevent future leaks. Documented existing conditions through photographs showing underside of floor structure near plumbing access points an

Completed comprehensive boiler inspection at basement location. Performed combustion analysis using digital diagnostic meter, recording oxygen levels at 20.8%, carbon monoxide at 0 ppm, pressure at 0.04, and flue temperature at 32.9°F. Inspected internal heat exchanger components, evaporator coils, and electrical connections including capacitor and wiring harness; all components found to be in operational condition with no immediate safety concerns identified.

Completed full HVAC system installation including 70,000 BTU furnace, 3-ton rear-discharge air conditioning unit with AHRI certification #215664802, humidifier, and liner. Installed 40-gallon hot water heater with pump and reconnected all necessary utilities. Performed pressure switch testing using diagnostic equipment, confirming proper system operation with readings of 6.76 and 6.86 inWC. Installed exterior PVC condensate drainage lines through brick exterior wall with proper termination and grading. Obtained mechanical and electrical permits for all installed equipment, and system qualifies for applicable utility rebates.

# HVAC Maintenance - Gold AC Inspection Completed comprehensive Gold AC inspection on a single-zone residential air conditioning system with basement-located air handler. Inspected Lennox EL18XCV5036 outdoor condensing unit utilizing HFC-410a refrigerant with 5 lbs 11 oz factory charge. Unit is less than 10 years old and was confirmed operational upon arrival. Performed thorough visual examination of outdoor condenser unit, verifying proper installation, secure mounting, and clearance from obstructions. Inspected fan assembly and protective grille for proper operation and structural integrity. Verified manufacturer labels and serial number documentation (5824D11851) were intact and legible. Examined electrical connections and confirmed unit specifications: single phase, 60 Hz operation with appropriate voltage ratings. Assessed condenser coil condition through louvered panels, checking for debris accumulation, damage, or airflow restrictions. Confirmed surrounding area was clear of

Responded to callback for water dripping from furnace following recent maintenance visit. Upon inspection, identified active condensate leak from furnace drain line and associated PVC piping connections in basement. Condensate drain pan was positioned beneath leak to collect water. Inspected all drain line connections, fittings, and trap assembly for proper sealing and alignment. Addressed leak source by resealing affected connection points and verified proper pitch on condensate drain line to ensure adequate drainage. Tested system operation to confirm condensate was flowing correctly through drain system without further leakage. Verified furnace operation and monitored for several cycles to ensure issue was fully resolved.

Completed routine preventative maintenance on both furnace and air conditioning system as part of prepaid service plan. Inspected 4-year-old gas furnace in basement, verified proper burner ignition and flame pattern, checked blower motor operation, tested safety controls including pressure switches, and confirmed all electrical connections were secure. Performed complete AC tune-up on outdoor Bryant condenser unit, including inspection of fan assembly, cleaning of coils, verification of electrical disconnect functionality, and overall system assessment. Both systems operating within normal parameters with no issues identified or repairs needed at time of service.

Installed REME HALO air purification bulb unit that was picked up from supply house under purchase order. Verified both locking mechanisms were present as requested by customer prior to installation and completed the scheduled service call.

Diagnosed and replaced malfunctioning primary sump pump system that was causing backup pump activation. Observed significant mineral buildup and corrosion on pump components with sediment accumulation in basin. Additionally, repaired stuck faucet handle and addressed leaking toilet issue during service call.

Provided estimate for replacement of 10+ year old AC unit and hot water tank located in basement. Current equipment is operational but showing signs of aging. Inspection revealed moisture damage around plumbing connections with visible water staining on walls, deterioration of trim with black mold presence, and potential water leakage affecting the surrounding infrastructure. Natural gas is available for replacement equipment.

Performed Gold Furnace Inspection on operational furnace under 10 years old located in basement. Inspected igniter/sensor probe and verified proper electrical connections. Observed burner assembly with clean blue flame pattern indicating correct combustion and proper system operation.

Performed a comprehensive tankless water heater flush service on a wall-mounted unit. Removed and cleaned the inlet filter screen, which contained significant debris accumulation. System was successfully flushed to remove mineral deposits, restoring optimal performance and efficiency.

Replaced faulty high limit switch on HVAC system after diagnosing system failure. Inspected and verified proper operation of motor components and electrical connections throughout the unit. All components now functioning within normal parameters with proper safety controls restored.

Diagnosed 10+ year old Ruud furnace that failed to produce heat after being inactive for 2 weeks. Identified faulty high limit switch and clogged condensate trap, which were replaced to restore proper system operation. Verified proper heating function before completing service.

Inspected humidifier valve in unfinished ceiling area per HVAC technician's request. Documented existing plumbing configuration with photos showing copper supply line and connection point. Valve assessment completed and findings documented in job #1292768.